CustomWorks Enforcer GSX2 Manual de montaje - Página 9

Navegue en línea o descargue pdf Manual de montaje para Juguete CustomWorks Enforcer GSX2. CustomWorks Enforcer GSX2 17 páginas.

Imprimir página

Shock Bag

Shock Assembly

Shock Bag

Bag J

Shock Assembly

Bag J

-Parts for

Step#1

1426

Qty 2

Short Shock Body

-Parts for

Step#2

1432

Qty4

Eyelet Cap

-Parts for

Step#3

1433

Qty4

Spring Collar

STEP #1

5230

1429 MED

1430 SHORT

NOTE: Put a few

drops of oil on the

O-Rings!

1425 MED

1426 SHORT

1434

TIP: To press clip in easiest, compress the

clip so the diameter is a little smaller.Insert

1250

open end of clip first, working counter-

1435

clockwise to the bent end as shown.

SHOCK FILLING INSTRUCTIONS:

1) Holding the

2) Slowly move the

shock upright,

shaft up and down

fill with oil until

several times to allow

air bubbles to escape

the top of the

body.

to the top.

SUGGESTED

40 WT R/C

SHOCK OIL.

6) Then the shaft

7) If the shock does not push

should push itself

out this far there is not enough

out to its full length

oil in it. Add just a little oil and

slowly.

try steps 5-6 again.

8) If the shockrebounds too fast , or you cannot

push the shaft in until the eyelet hits the body, there

is too much oil. Loosen the cap about X full turns

and pump out a small amount of oil by pushing the

shaft in. Retighten the cap and try steps 5-6 again.

1425

Qty 4

1430

Qty2

Med Shock Body

Short Shock Shaft

1431

Qty4

Threaded Cap

1488

Qty4

1407

Spring

Spring Bucket

BUILD 2 SHORT & 2 MED

LENGTH SHOCKS!

- USE #1429 SHAFT WITH

1436

#1425 BODY.

- USE #1430 SHAFT WITH

#1426 BODY .

- Attach 1436 Shock Piston to

Shock Shaft using 5230 E-Clips

to secure.

- Press 1250 O-rings into the

Shock Body followed by 1434

Shaft Guide. Retain using 1435

Clip.

3) Refill with

oil to the top

of the shock

body.

1429

Qty2

1434

Qty4

Med Shock Shaft

Shaft Guide

1:1

1437

Qty 4

Firm Bladder (BLACK)

Qty4

1408

Qty4

Mount Ball

STEP #2

- Snap Pivot Ball into the 5228 Ball End. Thread

the Ball End onto the Shock Shaft until the Ball

End is flush with the end of threads on the shaft.

- Press 1432 Eyelet Cap into 1431 Threaded

Shock Cap so that guide in the Eyelet Cap lines

up in the recess in the Threaded Shock Cap.

- Press the 1437 Firm Bladder (BLACK) into the

Threaded Shock Cap so the dome of the

bladder points away from the Eyelet Cap.

- Fill the Shock Body with oil to the top then

thread the Eyelet Cap assembly onto the

Shock Body until tight.

-NOTE: See shock filling tips for more

instructions.

4) Thread the Eyelet Cap

assembly onto the Shock

Body until it is hand

tight. Oil should seep

out of the bleed hole

in the Threaded Cap.

STEP #3

5277 Screw on

5277

the RF passes

thru the outer

RIGHT

most hole, 2nd

from the bottom.

FRONT

5277 Screw on

1488

the LF passes

SPRING

thru the inner

most hole, 3rd

from the bottom.

- Thread 1433 Spring Collar onto the

shock. Slide 1488 Spring onto the

shock and secure using the 1407

spring bucket as shown.

- Press 5277 Screws thru the locations

shown. Fasten using 2214 Standoff.

1250

Qty 8

1435

Qty 6

1436

O- Ring

Reatining Clip

Piston

5228

Qty4

Short Ball End

5274

5277

Qty 4

4-40 x 7/8 SH Screw

4-40 x 1/2 SH Screw

5) Move the shock shaft in and out a

few times and then push it all the way

in. It should be easy to push the shaft

in until the eyelet hits the body.

1408

5277 Screw

5217

passes thru the

inner most hole,

4th hole from the

1433

bottom row.

5274

1407

- Install the shocks onto the screws

with the shoulder of the 1408

Mount Ball facing away from the

tower, secure with 5217 Nut.

- Attach the shock to the susp

arms in the locations shown.

1:1

Qty4

5230 Qty 10

E-Clip

5228

Qty4

Pivot Ball

Qty 4

5217

Qty 4

4-40 Lock Nut

1431

1432

1437

5228

5277

LEFT

REAR

5217

1408

1433

5274