Alula RE603P Manual de instrucciones - Página 2

Navegue en línea o descargue pdf Manual de instrucciones para Sistema de seguridad Alula RE603P. Alula RE603P 2 páginas. Wearable action button

Imprimir página

Zone 1

Single Tap

Press and Release

(Once)

Zone 2

Double Tap

Press and Release

(Twice, <1 second

apart)

Zone 3

Press and Hold

Press and Hold (5 seconds)

Then release

The LED Ring blink patterns confirm each button press type detected:

Zone 1

Single Tap

One short blink +

On for 3 seconds

Zone 2

Double Tap

Two short blinks +

On for 3 seconds

Zone 3

Press and Hold

Three short blinks +

On for 3 seconds

The LED will remain on for approximately 3 seconds when transmitting.

Wait until the LED is OFF before attempting the next button press.

A Zone event transmission is sent as an Open immediately followed by a

Restore. Depending on the security panel's features, triggering each of

the Wearable Action Button's Zones can be set up as the initiating action

to trigger a pre-configured automation or rule. Refer to your specific

panel's instructions for more information.

8. Maintenance - Replacing the Battery

When the battery is low, a signal will be sent to the control panel.

To replace the battery:

•

Insert a plastic pry tool, or a small flat blade screwdriver into one of the

notches on the back of the Wearable Action Button and gently pry to

release the back cover from the main housing.

•

Set the back cover aside, and gently remove the circuit board from the

housing.

•

Remove the old battery and insert a new Panasonic CR2032 battery with

the positive side (+) of the battery touching the battery holder marked

with the (+) symbol.

Re-assemble by placing the circuit board into the back case with the

•

battery side facing down. Align the small notch on the side of the circuit

board with the tallest plastic rib on the inside wall of the back case. When

properly inserted, the circuit board will sit level inside back case.

•

Align the arrows of back cover and the main housing, then carefully snap

them together.

•

Test the Wearable Action Button to ensure proper operation.

WARNING: Failure to follow these warnings and instructions can lead to heat

generation, rupture, leakage, explosion, fire, or other injury, or damage. Do

not insert the battery into the battery holder wrong side up. Always replace

the battery with the same or equivalent type (see Specifications on page 1).

Never recharge or disassemble the battery. Never place the battery in fire or

water. Always keep batteries away from small children. If batteries are

swallowed, promptly see a doctor.

Always dispose and/or recycle used batteries in accordance with the

hazardous waste recovery and recycling regulations for your location. Your

city, state, or country may also require you to comply with additional

handling, recycling, and disposal requirements.

Product Warnings and Disclaimers

WARNING: CHOKING HAZARD - Small parts. Keep away from children.

WARNING: STRANGULATION AND CHOKING HAZARD – A user can suffer serious

personal injury or death if the cord becomes entangled or stuck on objects.

FCC Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Re-orient or relocate the receiving antenna

•

Increase the separation between the equipment and receiver

•

Connect the equipment to an outlet on a different circuit from the receiver

•

Consult the dealer or an experienced radio/TV contractor for help.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

C'et appareil est conforme la norme d'Industrie Canada exempts de licence RSS. Son fonctionnement est

soumis aux deux conditions suivantes: (1) c'et appareil ne peut pas provoquer d'interférences, et (2) c'et

appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais

fonctionnement de la dispositif.

FCC ID: XQC-WST130

IC: 9863B-WST130

Trademarks

Apple Watch is a registered trademark of Apple Inc.

All trademarks, logos and brand names are the property of their respective owners. All

company, product and service names used in this document are for identification purposes only.

Use of these names, trademarks and brands does not imply endorsement.

Warranty

Ecolink Intelligent Technology Inc. warrants that for a period of 2 years from the date of

purchase that this product is free from defects in material and workmanship. This warranty does

not apply to damage caused by shipping or handling, or damage caused by accident, abuse,

misuse, misapplication, ordinary wear, improper maintenance, failure to follow instructions or

as a result of any unauthorized modifications. If there is a defect in materials and workmanship

under normal use within the warranty period Ecolink Intelligent Technology Inc. shall, at its

option, repair or replace the defective equipment upon return of the equipment to the original

point of purchase. The foregoing warranty shall apply only to the original buyer, and is and shall

be in lieu of any and all other warranties, whether expressed or implied and of all other

obligations or liabilities on the part of Ecolink Intelligent Technology Inc. neither assumes

responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to

change this warranty, nor to assume for it any other warranty or liability concerning this

product. The maximum liability for Ecolink Intelligent Technology Inc. under all circumstances for

any warranty issue shall be limited to a replacement of the defective product. It is

recommended that the customer check their equipment on a regular basis for proper operation.

Ecolink is a trademark owned by Ecolink Intelligent Technology Inc.

RE603P Designed and manufactured by Ecolink Intelligent Technology Inc. 2023.

2055 Corte Del Nogal

Carlsbad, CA 92011

1-855-632-6546

www.discoverecolink.com

PN: 47007-00xxxxx

REV & REV Date: A02 01/12/2023