Alula RE617 Manual - Página 6

Navegue en línea o descargue pdf Manual para Sistema de seguridad Alula RE617. Alula RE617 9 páginas. Connect+ encrypted heat alarm

Imprimir página

Figure 5b - How to Remove

PUSH UP CATCH & TWIST

ALARM ANTI-CLOCKWISE TO REMOVE

If necessary to further secure the Alarm,

use a No.2 or No.4 self-tapping screw (see

Figure 5d) to firmly lock the Alarm and its

mounting plate together (see Figure 5c) -

NOT SUPPLIED.

Figure 5c

Figure 5d

SELF TAPPING

Attach the Alarm to the mounting plate.

Insert the screw (not supplied) on the "U"

shaped recessed area shown in Figure 5c.

To remove the Alarm from the ceiling,

remove the screw first, and then twist off

anti-clockwise.

6. Testing, Maintenance and

Power Supply Monitoring

Your Alarm is a life saving device and

should be checked periodically.

6.1 Manually Testing your Alarms

It is recommended that you test your Alarms

after installation and then at least weekly

to ensure the units are working. It will also

help you and your family to become familiar

with the sound of the Alarms.

- Press and hold the Test Button until the

Alarm sounds and the red light flashes (see

Figure 4). The Alarm will stop sounding

shortly after the button is released.

- Repeat this procedure for all other Alarms

in the system.

TAMPERPROOF SCREW

SCREW

2 to 3 mm

WARNING: DO NOT TEST WITH FLAME.

This can set fire to the Alarm and damage

the house. We do not recommend testing

with heat or flame as the results can be

misleading unless special apparatus is used.

When you press the Test button it simulates

the effect of heat in a Heat Alarm which it

could experience in a real fire.

6.2 Test/Silence Button to Control

Nuisance Alarms

The Heat Alarms have a combined Test/

Silence button to help you control nuisance/

false alarms.

If, when the Alarm sounds, there is no sign

of heat or noise to indicate that there is a

fire, it should be assumed that it is due to

an actual fire and the dwelling should be

evacuated immediately.

Check the house carefully in case there is a

small fire smoldering somewhere.

1. To cancel a false alarm from a Heat Alarm

(which has its red light flashing rapidly),

press the Test/Silence button (the Heat

Alarm will automatically switch to a reduced

sensitivity condition).

The Heat Alarm will be silenced for a period

of approximately 10 minutes. The red light

on the cover of the Heat Alarm will flash

every 8 seconds to indicate that the unit has

been silenced.

2. The Heat Alarm will reset to normal

sensitivity at the end of the silenced period

(10 minutes). If additional silenced time

is required, simply push the Test/Silence

button again.

3. If kitchen usage/layout is such that there

are an unacceptable level of nuisance

alarms, re-locate the Heat Alarm further

away where it will be less affected by

cooking fumes, etc.

We recommend the use of a Heat Alarm

in the Kitchen area to avoid such nuisance

alarms.

6.3 Power Supply Monitoring

6.3.1 What to do when an Alarm is

beeping:

A Heat Alarm is beeping about every 48

seconds with the yellow light flashing at the

same time:

- Replace the batteries.

6.3.2 Battery Replacement

When the batteries' power is low and

replacement is necessary, the Heat Alarm

will "beep" and the yellow light will flash at

the same time about once every 48 seconds

for at least 7 days. The batteries must then

be replaced. Also, replace the batteries if

the Alarm does not sound when the Test

Button is pressed. When you replace the

batteries, you must press the Test button

to check that the Alarm is functioning

correctly. Only replace the battery with

Panasonic

CR123A Batteries.

Dispose of used batteries promptly. Keep

away from children. Do not disassemble

and do not dispose of in fire.

Replacement batteries can be purchased at

your local hardware store.