DKS 1520 series Manual de instalación y del usuario - Página 11
Navegue en línea o descargue pdf Manual de instalación y del usuario para Lector de tarjetas DKS 1520 series. DKS 1520 series 16 páginas. Stand alone card readers or controller
También para DKS 1520 series: Manual (2 páginas)
Imprimir página
2.5 Card Code Programming
In the following programming sequence, the term "card code" is also used to reference any 26-bit wiegand device code that is
being used with the 1520. For example, digital entry codes or RF transmitter codes are also referred to as "Card Codes". Card
codes are always five-digits in length. Valid codes are 00000 – 65405.
Card codes can be programmed as a block of sequential codes or can be entered individually. When programming a single card
code, the beginning and ending card codes are the same. When entering a block of card codes, the 1520 will "beep" every few
seconds while the card codes are being programmed. When programming is complete, the system will emit a long beep. The
1520 will take about 1 minute to program 200 card codes. If different time zones will be assigned to different blocks of cards,
then these blocks will need to be programmed separately so that the correct time zones are applied. For example, if cards 01000
through 01010 are to be assigned time zone 1 (always GRANT entry), and cards 01011 through 01100 are assigned time zone
2, then these blocks have to be entered individually.
Each card code can be assigned two time zones. If using a single time zone, enter the time zone number twice in the two-digit
time zone field. For example, if using time zone 1 (always GRANT entry), enter 11 in step 4.
If you enter time zones that conflict with each other, the system evaluates each time zone individually starting with the first one.
For example, if 01 is entered in step 4, time zone 0 tells the unit to DENY entry while time zone 1 tells the system to always
GRANT entry. In this case, the system will first look at time zone 0, deny entry and then will look at time zone 1. Access will
then be GRANTED.
2.5.1 Programming a Single Card Code
1. Press
1 7 and enter the MASTER CODE. [
*
2. Enter the five-digit card number, then press
3. Enter the five-digit card number AGAIN, then press
4. Enter the two-digit time zone number, then press
Note: Two different time zones can be applied by entering two different numbers in the two-digit time zone field.
If ONLY using a single time zone (0 - 9), enter the time zone number twice in the two-digit time zone field.
Time zone 0 will always DENY entry.
Time zone 1 will always GRANT entry.
Time zone 2 - 5 are CARD programmable, see section 2.4.1.
Time zone 6 - 9 are HOLD programmable, see section 2.4.2.
5. Repeat steps 1 - 4 to enter additional card codes, one at a time.
Note: Card codes not programmed in the 1520 will not print or be stored in the transaction buffer. If you want a transaction of
denied card codes (for example - a lost card), then assign time zone 00 (always deny entry) in step 4.
2.5.2 Programming a Block of Card Codes
1. Press
1 7 and enter the MASTER CODE. [
*
2. Enter the five-digit BEGINNING card number, then press
3. Enter the five-digit ENDING card number, then press
4. Enter the two-digit time zone number for these cards, then press
Note: Two different time zones can be applied by entering two different numbers in the two-digit time zone field.
If ONLY using a single time zone (0 - 9), enter the time zone number twice in the two-digit time zone field.
Time zone 0 will always DENY entry.
Time zone 1 will always GRANT entry.
Time zone 2 - 5 are CARD programmable, see section 2.4.1.
Time zone 6 - 9 are HOLD programmable, see section 2.4.2.
5. The system will emit a short beep every few seconds while programming the card codes.
When the short beeps stop, wait approximately 20 seconds for a long beep - programming is complete.
1520-065-E-7-16
1 7 _ _ _ _ (beep)]
*
. [ _ _ _ _ _
(beep)]
*
*
. [ _ _ _ _ _
(beep)]
*
*
. [ _ _
(beep) followed by Long Beeeep - programming ends]
*
*
1 7 _ _ _ _ (beep)]
*
. [ _ _ _ _ _
*
. [ _ _ _ _ _
(beep)]
*
*
. [ _ _
*
(beep)]
*
(beep)]
*
9