Fleck 5600SXT Manual de instalación - Página 14

Navegue en línea o descargue pdf Manual de instalación para Dispensador de agua Fleck 5600SXT. Fleck 5600SXT 14 páginas.
También para Fleck 5600SXT: Manual de instrucciones de instalación (19 páginas), Programación (3 páginas)

Imprimir página

8 › I n I t I a l s ta R t- u P

1) With one nearby softened faucet running in the COLD position, slowly open your bypass valve or 3-valve bypass

to about ¼ open to allow the air trapped in the softener to escape via your running faucet.

bypass too quickly or too open may damage your softener or plumbing

2) Allow the softener tank to slowly fill with water. After a few minutes, you will see a trickle of water coming from

the cold water faucet. Allow the water to run slowly in this manner for an additional 5 minutes. Next, with the

cold water faucet still running, gradually move your bypass valve to the fully open position.

some initial discoloration from the softened water – this is normal and should dissipate within the first

40-50 gallons of water used.

To test the integrity of your new system and all connections

3) i

form a short form regeneration to check for leaks before service.

5 gallons of water/the amount of water needed to cover the brine grid into the brine tank. Start the regeneration se-

quence by HOLDING the REGEN button for 5 seconds. Once the screen stops flashing BW, let BW - Backwash run

for about 1 minute to observe the water leave out the drain line and check for leaks. If you notice any leaks,

page 10

to review preparing the drain connection. Click the REGEN button ONCE to move on to BD - Brine Draw

4) Once the screen stops flashing BD, let BD - Brine Draw run for about 1 minute to observe the water level in the

brine tank being drawn lower. Also check the brine line and the float valve in the brine well for leaks. If the water

level doesn't lower or there is a leak,

Click the REGEN button ONCE to move on to RR - Rapid Rinse

5) Once the screen stops flashing RR, advance from RR - Rapid Rinse to BF - Brine Fill by clicking the REGEN button

ONCE more. Once the screen stops flashing BF, let BF - Brine Fill run for about 1 minute to observe the water

level in the brine tank rise. Also check the brine line and float valve in the brine well for leaks. If the water level

doesn't rise or there is a leak,

REGEN button ONCE to finish

6) Now you may add 120-160 pounds of pellet, solar, or block salt to your brine tank.

filled with salt to at least above the water level.

installation as the new resin arrives at full softening capacity. Simply let your softener meter automatically trigger

regenerations by tracking the water consumption

› C o n G R at u l at I o n s

Your new softener with Fleck 5600 SXT Meter Valve is now properly in-

stalled and programmed! Please maintain your system by keeping the softener

plugged-in and always keep your brine tank filled with salt to at least above

the water level. We appreciate your business, and hope that you enjoy years of

trouble-free softened water!

PAGE 14

F I G u R e 14 - a

Turn off the running cold water faucet when the water runs clear

return to pages 9 and 10

You do not need to perform a regeneration immediately after

QualityWaterForLess.com

19) The system will now exit Master Programming

mode and the display should now show the

time of day followed by the number of gal-

lons remaining as shown in Figure 14-A. Now

change the time of day to your current time

with either the UP or DOWN button.

ful to note the presence or absence of the

PM indicator in the top right corner.

the time with the REGEN button

it is strongly encouraged that you per-

Begin this process by adding approximately

to review preparing the brine tank connection.

to review preparing the brine tank connection. Click the

Be care-

Confirm

noTe: opening the

noTe: You may see

return to

always keep your brine tank

Help: 888-426-5001