Cygolite Expilion Manual de instrucciones - Página 2

Navegue en línea o descargue pdf Manual de instrucciones para Accesorios para bicicletas Cygolite Expilion. Cygolite Expilion 2 páginas. Super bright usb rechargeable bicycle lighting system

Imprimir página

Cygolite Expilion Manual de instrucciones

HEADLIGHT OPERATION

The Expilion features a BICYCLE MODE (5 settings) and a SPECIAL

MODE (3 settings). The settings are controlled by the power button which

also functions as the low battery and charging indicator. The diagram and

instructions below indicate where these features are located on the

headlight and how to use them.

CAUTION: The light may get hot during use. Handle with care and turn

light off if stationary for more than 10 minutes.

USB port

Battery stick

BICYCLE MODE (5 settings)

(Med > High > Boost > Low > 2-in-1 SteadyPulse)

1. Press power button to operate in bicycle mode. The light will turn on in

the Medium setting and the button will illuminate.

2. Press power button to scroll through the bicycle settings.

3. Hold the power button for 2 second to turn the light off.

NOTE: Boost setting is the brightest setting in bicycle mode. The power

button will blink slowly when boost setting is on.

SPECIAL MODE (3 settings)

(Day Flash > Walking > SOS)

1. (While the headlight is off) Press and hold the power button for

2 seconds to operate in special mode.

2. Press power button to scroll through the 3 special settings.

3. Press and hold power button for 2 second to turn the light off.

24/7 Safety Technology

: Night and day modes give added visibility

2-in-1 SteadyPulse

: Alerts nearby motorists with triple pulses while

constantly lighting your path at night.

Day Flash: Intensly bright flashes demands motorist's

attention in peak daylight.For daytime use only.

LOW BATTERY INDICATOR

As the battery runs low, the illuminated power button will fast flash indicating

approximately 10~15 minutes of power left. At this time we recommend stop

using the light and recharging it immediately.

MOUNTING ON HANDLEBARS

1. Attach handlebar spacers to inside of handlebar bracket for standard

sized handlebars. Remove spacers for oversized handlebars.

2. Attach rubber pad to handlebar spacer (or handlebar bracket) for grip.

MOUNTING CONTINUED

Attach Handlebar spacers

(for standard sized bars)

Rubber pad

3. Wrap bracket around handlebar, return thumbnut in slotted space, twist

Power Button

thumbnut clockwise to tighten

(During use)

4. Slide headlight back into the bracket until headlight clicks into place.

Solid

= Light on

5. To remove headlight, press the release tab on the bracket down and

Fast flash

= Low battery

slide headunit forward.

Slow blink

= Boost mode

ADJUST THE SIDE-TO-SIDE BEAM DIRECTION

Swivel the headlight left to right to adjust the side-to-side direction. If side

swivel becomes loose, tighten the swivel screw on the top of the bracket

with a philips screwdriver.

INSTALLING BATTERY

1. Align the arrow on the back of the battery and the arrow on the back

of the headlight that reads "O", then insert battery completely.

2. Turn battery clockwise completely (until battery arrow is aligned with

"C" arrow on headlight) to lock battery into the headlight.

3. Reverse step 1 and 2 to remove the battery.

BATTERY CHARGING

Rubber Cover

Charging Port

WARNING: We recommend to charge the battery with the supplied charger

or USB cable. If using another USB charger, check the power button to

verify the light is taking a charge. The charger is for indoor use only.

Release Tab

Thumbnut

Open

Power Button

(During charging)

Flash

= Charging

Solid

= Full

BATTERY CHARGING - continued

1. Lift the RIGHT side of the rubber cover to reveal the charging port.

STEP 2 VARIES DEPENDING ON CHARGING METHOD.

2A. (Wall charging) Connect the charger to the wall outlet.

2B. (Computer USB charging) Connect USB cable to computer USB port.

3. Insert charging cable into the USB charging port on back of light.

4. The power button on top of the light will flash green when charging

then have a steady green when fully charged.

5. Allow approximately 5 continuous hours to fully charge a drained

battery. (Charging times may vary depending on charging method)

REINSTALLING USB COVER:

1. Insert the left inner edge of the

USB cover into the recharging port.

2. Apply pressure diagonally inward to

the right side of the cover until the

USB cover is fully inserted.

If USB cover does not stay seated in the hole, add lubricant to the

inside of the cover to slide and stay in the hole more easily.

RUN TIMES

Bicycle Modes (hr:min)

Model

Med

High

Boost

Low

S-Pulse

EXPILION

2:15

1:15

HELMET MOUNT

(select models only, see package for details)

Add foam pad

Helmet bracket (bottom view)

1. Add foam pad to bottom of helmet bracket to cushion against helmet.

Peel away paper to reveal adhesive and fasten to the helmet bracket.

2. Weave the 12" long velcro strap up through one hole of the helmet

bracket, then down through the outer hole on the other side. Pull the

strap until the plastic loop prevents the strap from moving further.

3. Position helmet bracket over vent holes on the front top of the helmet.

4. Insert velcro strap downward through the vent hole then up through the

opposing vent hole. Thread the velcro strap through the velcro strap loop

and pull to tighten. Then fasten the velcro strap to itself, making sure the

helmet bracket is secured in place.

5. Sliding backward, insert the headlight into the helmet bracket until it locks

in place. To remove headlight, press the bracket tab down and slide the

headlight forward.

Special Modes

Day Flash

Walking

SOS