Doheny's 2827 Manual - Página 3

Navegue en línea o descargue pdf Manual para Cables y conectores Doheny's 2827. Doheny's 2827 3 páginas. Deluxe above ground solar reel system

Imprimir página

G Attach Solar Cover to Reel

1. Your Solar Cover should be in the pool and trimmed

to the inside of your pool's top rail. Make a mark

with marker at each edge of the cover directly

below tube.

2. Remove cover from pool and lay flat on ground.

Draw a straight line between the two marks on

the cover.

3. Roll cover up until you reach your drawn line and

measure in 8 in. from each side of cover and place

a cross mark on the line.

4. Next, take the measurement used between the first

pole marks and equally space the 3 remaining

marks down the line to the second 8 in. measurement.

5 Evenly Spaced Marks

Rolled up Blanket

H Attach Nylon Plates & Fabric Straps to

Solar Cover

1. Start with the first 8 in. mark from the folded edge

of the cover.

2. Attach a Nylon Plate to the cover on the drawn

line by pulling a double thickness of the cover into

the Nylon Plate (shown in illustration A).

3. Take a second Nylon Plate and place directly

underneath the first Nylon Plate. Use a sharp

instrument (such as a Philips screwdriver) and

punch holes through the first Nylon Plate, then

the cover, ending with the second Nylon Plate.

Make certain that the holes are clean of excess

cover material.

4. Insert the Nylon Bolts through the Nylon Plate,

then through an open hole of a corresponding

Fabric Strap which is already attached to the Pole,

then the cover, and finish with the other Nylon

Plate. Secure with Nylon Nuts (see illustration B).

5. Continue attaching the remaining 4 sets of Nylon

Plates and Straps to your Solar Cover at each mark

shown in step G (above).

6. The last set of plates and last strap should be 8 in.

from the opposite edge of the cover (see illustration C).

10411 80th Avenue Pleasant Prairie, WI 53158 | Orders and Customer Care: 1-800-574-7665 | Fax: 1-800-323-5932 | Doheny.com

Strap

Nylon

Bolts

Nuts

Strap

Plates

Solar Cover bubbles

should be face down.

Cover is folded

between strap plates.

I Operating Instructions

1. After Reel System is assembled on your pool,

slowly turn wheel clockwise; the cover will be lifted

up and over the pole. Should either cover edge

be hampered by the top rail, straighten it out so that

the cover remains smooth and wrinkle-free during

roll-up. Make certain the cover is removed from the

pool uniformly onto pole (see diagram below).

2. When the cover is completely rolled up on the pole,

lift the wheel, pole and yoke and rotate system to

any desired location.

3. If desired, reel system may now be removed from

top rail and stored.

J Return Reel System to Pool

1. Place Reel System back onto pool by sliding base

units into rail attachments, then sliding pole with

Solar Cover into base units.

2. Turn Wheel counter clockwise until cover makes

contact with the pool.

3. Separate the two edges of the cover from each other.

4. Grip cover edge and walk slowly down the pool to

the end.

5. Roll out 5-8 feet of cover at a time.

6. Now walk the cover down to the end of the pool.

7. Repeat procedure for second part of cover.

Helpful Hints

Remove Reel System at the end of each season.

Clean Wheels, Hubs, Yokes, Bearings, and Bases with

warm soapy water.

Storage

Always store the Reel System in a safe place.

MANUFACTURER IS NOT RESPONSIBLE FOR

ACCIDENTS OR DAMAGE RESULTING FROM

UNSAFE STORAGE.