Ambient Technologies RCB Instrucciones de instalación y funcionamiento - Página 2
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Mando a distancia Ambient Technologies RCB. Ambient Technologies RCB 2 páginas. Basic on/off remote control
También para Ambient Technologies RCB: Instrucciones de instalación y funcionamiento (2 páginas), Instrucciones de instalación y funcionamiento (5 páginas)
Imprimir página
OPERATIONS:
Transmitter:
General:
The RCB is an On/Off remote control.
The transmitter will operate the remote
receiver from 1foot to a maximum of 30
feet. The operational range is reduced
when batteries are low or when the
receiver is inside a metal enclosure.
Initial start up:
1. After initial power up, the transmitter is ready for use.
Manual Mode:
1.Press the ON button once to turn on the appliance. Press the
OFF button to turn it off.
Low-battery detection:
1.When the battery voltage drops to a certain level, the LED on
the transmitter will blink until the battery expires. Change the
battery before the battery is too weak for normal operation.
TURN THE UNIT OFF BEFORE REPLACING
BATTERIES.
Receiver:
Slide Switch:
1.ON position: the system will remain on until the slide switch is
placed in the OFF or RS position.
2.RS position: the system will only operate if the remote receiver
receives a signal from the transmitter.
3.OFF position: the system is off. The slide switch should be
placed in the OFF position if you will be away for an extended
period of time. If the remote receiver is mounted out of
children's reach, the OFF position also functions as a safety
device by both turning the system off and rendering the receiver
inoperable.
TESTING YOUR NEW REMOTE CONTROL
SYSTEM
1.Connect the wiring terminal to the appliance. Refer to the
appropriate Homeowner's Manual for proper wiring connections
to the appliance.
2.Light your gas appliance following the appliance lighting
instructions that came with the appliance. Confirm that the pilot
light is on; it must be in operation for the remote control to
operate the main gas valve. Appliance control knob must be in
the ON position. Appliance ON/OFF switch must be in OFF
position.
3.Slide the 3 position button on the remote receiver to the ON
position. The main gas flame should ignite.
4.Slide the button to OFF. The flame should extinguish (the pilot
light will remain on).
5.Slide the button to RS (the center position), then press the ON
button on the transmitter to turn the system to ON. The main
gas flame should ignite.
6.Press the OFF button on the transmitter to turn the system to
OFF. The flame should extinguish (the pilot light will remain
on).
Symptom
LED
1. LED light on receiver
blinking or battery icon
on LCD on transmitter.
4. Appliance does not
come on after pressing
ON on transmitter
ON
OFF
5. Receiver cannot receive
signal.
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following meas-
ures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This warranty gives you specific legal rights and you may also
have other rights that vary from state to state or province to
province. Answers to any questions regarding our limited warran-
ty may be obtained by writing our corporate offices.
Ambient Technologies warrants each new Ambient Technologies
remote control against any defects that are due to faulty material
or workmanship to the original owner, for a period of five years
after the original date of purchase. This warranty and our liability
does not apply to batteries, nor does it include damage to mer-
chandise or the remote control resulting from accident, alteration,
neglect, misuse, improper installation or any other failure to fol-
low Ambient Technologies installation and operating instructions.
Ambient Technologies agrees to repair or replace at its option any
Ambient Technologies remote control under warranty provided it
is returned postage prepaid to our warranty facility in a padded
carton within the warranty period, with proof of the original date
of purchase and a brief description of the malfunction. This limit-
ed warranty does not include the cost of removal or re-installation.
TROUBLESHOOTING
Causes
Action
1. Low Battery
1. Replace batteries. Change
batteries every 6 months.
1. Wiring / Electrical
1. Slide the switch to ON, if
Connections
appliance comes ON,
wiring is not the causes.
2. If appliance does not
come on, check wiring
connections.
2. Privacy (DIP) switch
1. Make sure the transmitter
setting on transmitter
and receiver has the same
does not match
DIP switch settings.
receiver
3. Distance between the
1. Make sure the operating
transmitter and
distance is less than 30
receiver is more than
feet
30 feet
1. Receiver is installed
1. Make sure the receiver is
in an enclosure
not located inside an
enclosure.
WARRANTY
Ambient Technologies
149 Cleveland Drive
Paris KY 40361
FOR TECHNICAL SUPPORT
CALL 800-398-6195
50D0035 Rev 2 July 2002