Ambient Technologies RCBE Instrucciones de instalación y funcionamiento - Página 2
Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Mando a distancia Ambient Technologies RCBE. Ambient Technologies RCBE 2 páginas. Basic on/off remote control – 120vac
Imprimir página
Receiver
Optional 6 Hour Shutdown
1. The receiver comes preset from the factory with a 6 hour
shutdown from its last ON operation. This is done to pre-
vent the appliance from continuing to run if unattended.
2. You may disable this feature if you wish. To disable,
change the receiver privacy (DIP) switch #1 ONLY to the
OFF position. Make sure the transmitter privacy (DIP)
switches are set the same. Follow the instructions on
Setting Privacy (DIP) Switch on Receiver & Transmitter
discussed early in this manual.
3. By disabling this feature, your appliance may continue to
run unattended.
Slide Switch
1. ON position: the system will remain on until the slide
switch is placed in the OFF or RS position.
2. RS position: the system will only operate if the remote
receiver detects a signal from the transmitter.
3. OFF position: the system is off. The slide switch should be
placed in the OFF position if you will be away for an
extended period of time. If the remote receiver is mounted
out of children's reach, the OFF position also functions as
a safety device by both turning the system off and render-
ing the receiver inoperable.
TESTING YOUR NEW REMOTE CONTROL SYSTEM
1. Connect the wiring terminal to the appliance. Refer to the
appropriate Homeowner's Manual for proper wiring con-
nections.
2. Light your gas appliance following the lighting instruc-
tions that came with the appliance. Confirm that the pilot
light is on; it must be in operation for the remote control to
operate the main gas valve. Appliance pilot control knob
must be in the ON position. Appliance ON/OFF switch
must be in OFF position.
3. Slide the 3 position button on the remote receiver to the
ON position. The main gas flame should ignite.
4. Slide the button to OFF. The flame should extinguish (the
pilot light will remain on).
5. Slide the button to RS (the center position), then press the
ON button on the transmitter to turn the system to ON.
The main gas flame should ignite.
6. Press the OFF button on the transmitter to turn the system
off. The flame should extinguish (the pilot light will
remain on).
TROUBLESHOOTING
Symptom
Causes
Action
1. LED light on transmitter
1. Low Battery
1. Replace batteries.
blinking
Change batteries every 6
months.
4. Appliance does not come
1. Wiring / Electrical
1. Slide the switch to ON, if
on after pressing ON on
Connections
appliance comes ON,
transmitter
wiring is not the cause.
2. If appliance does not
come on, check wiring
connections.
3. Check to make sure the
receiver is plug into 120
VAC outlets.
2. Privacy (DIP) switch
1. Make sure the transmitter
setting on transmitter
and receiver has the same
does not match
DIP switch settings.
receiver
3. Distance between the
1. Make sure the operating
transmitter and
distance is less than 30
receiver is more than
feet
30 feet
5. Receiver cannot receive
1. Receiver is installed
1. Make sure the receiver is
signal.
in an enclosure
not located inside an
enclosure.
2. 120VAC is not
2. Connect receiver adaptor
connected
to 120VAC power supply.
WARNING: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation.
f i r e - p a r t s . c o m
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful inter-
ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following meas-
ures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
WARRANTY
This warranty gives you specific legal rights and you may also
have other rights that vary from state to state or province to
province. Answers to any questions regarding our limited warran-
ty may be obtained by writing our corporate offices.
Ambient Technologies warrants each new Ambient Technologies
remote control against any defects that are due to faulty material
or workmanship to the original owner, for a period of five years
after the original date of purchase. This warranty and our liability
does not apply to batteries, nor does it include damage to mer-
chandise or the remote control resulting from accident, alteration,
neglect, misuse, improper installation or any other failure to fol-
low Ambient Technologies installation and operating instructions.
Ambient Technologies agrees to repair or replace at its option any
Ambient Technologies remote control under warranty provided it
is returned postage prepaid to our warranty facility in a padded
carton within the warranty period, with proof of the original date
of purchase and a brief description of the malfunction. This limit-
ed warranty does not include the cost of removal or re-installation.
All Ambient returns must have a return authorization number from
Ambient Technical Support.
Ambient Technologies
149 Cleveland Drive
Paris KY 40361
FOR TECHNICAL SUPPORT
CALL 800-398-6195
50D0075 Rev 2 Mar 2006