Ambient Technologies RCST Instrucciones de instalación y funcionamiento

Navegue en línea o descargue pdf Instrucciones de instalación y funcionamiento para Mando a distancia Ambient Technologies RCST. Ambient Technologies RCST 2 páginas. Standard thermostatic on/off remote control

Imprimir página

RCST

Standard Thermostatic On/Off Remote Control

INSTALLATION AND OPERATING

INSTRUCTIONS

This wireless thermostatic on/off/ remote control system provides a

safe, reliable, and user-friendly remote control for millivolt valve gas

appliances. The system can be thermostatically or manually turned

on and off with the transmitter. Always check the appliance home

owner's manual for additional information, or warnings regarding

accessory installation before connecting this remote control system.

Carefully inspect the contents for shipping damage. If any parts

are missing or damaged, immediately contact the dealer from whom

you purchased the kit. Do not attempt to install any part of the kit

unless all parts are in good condition. Please keep these instructions

for future reference.

CONTENTS OF KIT

Description

Quantity

Transmitter

Battery Alkaline AAA (for Transmitter)

Battery Alkaline AA (for receiver)

Receiver (Assembly) consists of:

Receiver Box

Slide Button–Black (On/RS/Off)

Wall Cover Plate–Black

Wall Cover Plate–White

Slide Button–White (On/RS/Off)

Battery Door–White

Plug-In Wiring Assembly – 22" Inches

Velcro (Loop and Hook)

Installation Instructions

#6 3/4" Screws, Zinc (for Wall Cover Plate)

#8 Screws (for ﬁ replace system control covers)

NOTE: Due to the sensitive temperature monitoring components in

the transmitter, it is necessary to allow the transmitter to stabilize to

room temperature before accurate room temperatures are dis-

played. If the transmitter is activated from a severe cold condition,

allow 15 minutes for accurate temperature readings to appear on

the LCD.

WARNING: Important Safety Information

• Read this manual thoroughly prior to installing, pro-

gramming or operating any remote control.

•

This remote control system is designed for use with a millivolt

or 24V gas valve system. Do not use this remote control sys-

tem on applications with voltages above 24 Volts AC/DC and

1 amp current.

•

This remote control system requires three (3) "AAA" and

four (4) "AA" alkaline batteries to power the transmitter and

receiver.

•

Wiring must conform to appliance requirement and building

codes/ordinances as required by local and national code

authorities having jurisdiction.

•

Do not short (or jumper) across the gas valve terminals to

test the remote control installation. This could damage the

unit and void the warranty.

•

This remote control system should only be used as described

in this manual. Any other use is prohibited and will void the

warranty.

50D0095 RCST.indd 1

FEATURES/SPECIFICATIONS

• Easy Access Thermostatic Control

• Battery Powered Transmitter and Receiver

• Low battery Indication

• Child Proof Lock-out

• 16 Security Codes

• Quick Disconnect Wiring Assembly

• Reset Button

WARNING: Turn appliance OFF and allow to cool before

installing or servicing. DO NOT connect 110-120 VAC

wiring to the millivolt gas control valve. The remote

operator must be installed exactly as outlined in these

instructions. Read all instructions completely before attempting

installation. Follow instructions carefully during installation. Any

modiﬁ cation of components will void the warranty and may cause

a ﬁ re hazard.

WARNING: Turn appliance OFF (at the appliance or

remote receiver) if you are away from your house for a

long period of time.

INSTALLATIONS

Receiver

The remote receiver may be wall mounted or

installed in the appliance per the appliance

homeowner's manual. Refer to the Homeown-

er's Manual for special installation instructions.

If wall mounted, the remote receiver must be

installed in a junction box with cover plate provided. Failure to follow

the installation instructions found in the appropriate Homeowner's

Manual will void the warranty and may cause a ﬁ re hazard.

Installing Batteries

The remote receiver uses four (4) "AA" batter-

ies. To install batteries:

1. Open the battery door by pressing the two

tabs located on the door.

2. Install the batteries as indicated in the receiver cover.

3. Close the battery door until the door tab snaps in place.

4. To install the receiver into a wall junction box, snap wall cover

plate to the receiver and install the receiver with the screws pro-

vided to the junction box.

5. The batteries should be replaced at least once every 6 months

or when the battery indicator ﬂ ashes.

Connecting the Receiver to your Appliance

This system comes with an 22 inch wire assembly. Insert the

white terminal to the back of the receiver. The terminal wire

block can only be installed one way. Do not force the terminal

plug onto the receiver.

Connect the wiring terminal two (2) 1/4" female spade terminals to

the appliance. Refer to the appropriate Homeowner's Manual for

proper wiring connections to the appliance. Your appliance may

have other options to con-

Receiver

Millivolt Valve

nect wiring from receiver.

Connect to the two (2) 1/4"

female spade wiring termi-

nals. Wire can be no longer

than 20 feet.

WARNING: Make sure that the wires do not contact the

appliances any place other than at the terminals. Expo-

sure to temperatures higher than 250ºF (105ºC) may

cause the receiver to malfunction or cause a ﬁ re hazard.

Transmitter

Installing Batteries

The remote transmitter uses three (3) "AAA"

batteries. To install batteries:

Battery

1. Press down the battery door tab and lift

Door Tab

up and remove the battery door.

2. Install the batteries as indicated on

transmitter.

3. Close the battery door by snapping in

place.

4. The batteries should be replaced at least

once every 6 months or when the battery

indicator ﬂ ashes.

Back of Transmitter

5. Press down the battery door tab and lift up and remove the bat-

tery door.

6. When both batteries are installed, the transmitter will initialize for

10 seconds and then is ready for use.

7. The batteries should be replaced at least once every 6 months

or when the battery icon indicator ﬂ ashes.

Setting Privacy (DIP) Switch on Receiver and Transmitter

The remote receiver and transmitter privacy (DIP) switches are pre-

set at the factory. In the event of activation or interference from other

nearby transmissions, reset the code using the following procedure:

1. Slide the code switches on the transmitter or receiver to your

choice of ON or OFF position. Switches #1, #2, #3 and #4 are

preset to "ON" for both the transmitter and receiver.

2. The switches on the transmitter and receiver must match in order

for the system to work.

3. To check, touch either the On or Off button on the transmitter

and the receiver indicator light will blink. If not repeat step 2.

4. The system is now ready to operate.

Transmitter

Dip Switch (Default)

Receiver

Reset Button

The reset button can be used to reset the transmitter if transmitter is

not working properly. The reset button is located behind the battery

door cover. Using a paper clip, press the reset button and the trans-

mitter will reset and initialize for 10 seconds before it can be used.

WARNING: Do not use two (2) or more remote control

systems in the same area with the same dip switch

settings, as they will communicate with each other. This

may cause the appliances to malfunction.

12/30/2014 9:07:10 AM