Flomec QS200 Manuel du propriétaire du produit - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire du produit pour {nom_de_la_catégorie} Flomec QS200. Flomec QS200 16 pages. Insertion ultrasonic flowmeter options for large pipe sizes
Également pour Flomec QS200 : Manuel d'installation (8 pages), Manuel du propriétaire du produit (20 pages)
Imprimer la page
tools.eps
UNPACKING
Contents:
box.eps
920913-01 Quick Start Guide (QS200 Saddle)
(1) Saddle (sized specifically for your pipe O.D.)
tools.eps
magnify_2.eps
(2) Band Clamps
tools.eps
(1) Retention Pin (Quick Release)
box.eps
warning symbol.eps
(1) Sensor Owners Manual
box.eps
Inspect
magnify_2.eps
measure.eps
magnify_2.eps
•
After unpacking the unit, inspect carefully for any damage that may
have occurred during transit. Check for loose, missing or damaged
parts. Shipping damage claims must be filed with carrier.
warning symbol.eps
plug.eps
warning symbol.eps
•
See General Safety Instructions, and all Cautions, Warnings, and
Dangers as shown.
measure.eps
oil.eps
measure.eps
To do a complete and successful installation, you must carefully read this manual
and the manual for the sensor.
plug.eps
megaphone.eps
plug.eps
BEFORE CUTTING A HOLE IN THE PIPE
•
Verify you have all the pieces.
oil.eps
biohaz.eps
oil.eps
•
Verify this saddle size is the same as your pipe outside diameter.
•
Verify the pipe is not pressurized.
megaphone.eps
Battery_Caution1.eps
•
Verify the desired hole location is more than 10 diameters downstream
megaphone.eps
and 5 diameters upstream from any obstructions. Valves, pumps,
elbows, reducers are all considered obstructions.
biohaz.eps
•
Note that the finished hole diameter should be between 1-15/16" to 2".
Caution.eps
biohaz.eps
It should be clean and free of burrs.
•
We recommend the hole be made with a hole saw.
Battery_Caution1.eps
Crush_Caution1.eps
Battery_Caution1.eps
•
Note the direction of flow. Measuring water only.
Caution.eps
Tools and Materials Needed
Electrical_Caution.eps
Caution.eps
tools.eps
•
Ø1-15/16" to Ø2.0" hole saw and drill
•
7/16" end wrenches
Crush_Caution1.eps
Face_protection.eps
•
Tape measure
Crush_Caution1.eps
box.eps
•
Permanent marker
Electrical_Caution.eps
Fall_Hazard.eps
Electrical_Caution.eps
magnify_2.eps
Heavy_Hazard.eps
Hot_surface.eps
(1) Sleeve
(1) Gasket
Heavy_Hazard.eps
Recycle.eps
Hardware
Heavy_Hazard.eps
(1) Sensor
(if ordered)
Hot_surface.eps
Resp_protection1.eps
Hot_surface.eps
Recycle.eps
Resp_protection2.eps
Recycle.eps
Resp_protection1.eps
Temp_Caution1.eps
Resp_protection1.eps
Resp_protection2.eps
body_protection.eps
Resp_protection2.eps
Temp_Caution1.eps
chemical_Caution.eps
Temp_Caution1.eps
body_protection.eps
ear_protection1.eps
body_protection.eps
chemical_Caution.eps
explosive_caution.eps
chemical_Caution.eps
ear_protection1.eps
eye_protection1.eps
ear_protection1.eps
explosive_caution.eps
foot_protection.eps
explosive_caution.eps
eye_protection1.eps
hand_protection.eps
eye_protection1.eps
Heavy_Hazard.eps
foot_protection.eps
foot_protection.eps
Hot_surface.eps
hand_protection.eps
hand_protection.eps
Recycle.eps
3