AMD DIrect SSRFR-21S Manuel de l'utilisateur - Page 5
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} AMD DIrect SSRFR-21S. AMD DIrect SSRFR-21S 9 pages.
Imprimer la pageBEFORE OPERATING
Shipment Arriving Damaged:
VISIBLE DAMAGE
If your shipment arrives with visible damage to the
box/carton, be sure the damage is noted on the
bill of freight or express receipt and signed by the
person making the delivery. File a claim for damages
immediately, regardless of the extent of damage.
CONCEALED DAMAGES
If damages are unnoticed until the refrigerator is
unpacked, notify the transportation company or
carrier immediately and file a concealed damage
claim with them. This should be done within (5)
days of the delivery date. Be sure to hold on to
the box/carton for inspection. We cannot assume
responsibility for damage or loss incurred in transit.
Important Notes:
BEFORE USING YOUR APPLIANCE
Remove the exterior and interior packing.
Before connecting the appliance to the power
source, let it stand upright for approximately
24 hours. This will reduce the possibility of a
malfunction in the cooling system from handling
during transportation. Clean the interior surface with
lukewarm water using a soft cloth. Install the handle
on the door if not already attached.
It is recommended that you install the appliance
in a place where the ambient temperature is
between 60°F and 90°F (16°C-32°C). If the ambient
temperature is above or below recommended
temperatures, the performance of the unit may
be affected. For example, placing your unit in
extremely cold or hot conditions may cause interior
temperatures to fluctuate. The operating temperature
range may not be reached.
1
21" REFRIGERATOR USER MANUAL
Parts & Features
1. Interior Light Cover
7. Door Bar (2)
2. Temperature Control Knob
8. Can Dispenser
3. Wire Shelves
9. Condiment Bar
4. Glass Shelf
10. Door
5. Drawer
11. Bottom Hinge
6. Leveling Leg
12. Top Hinge
13. Top Hinge Cover
BEFORE INSTALLING YOUR UNIT
• Remove the exterior and interior packing.
• Check to be sure you have all of the following
parts:
• 3 Shelves
• 1 Glass Lid
• 1 Crisper
• 1 Instruction Manual
• Before connecting the unit to the power source,
let it stand upright for approximately 2 hours.
This will reduce the possibility of a malfunction
in the cooling system from handling during
transportation.
• Clean the interior surface with lukewarm water
using a soft cloth.
INSTALLING YOUR UNIT
• This appliance is designed to be freestanding
only, and should not be recessed or built-in.
• Allow 5 inches of space between the back
and sides of the unit. This ensures proper
air circulation to cool the compressor and
condenser.
• Place your unit on a floor that is strong enough
to support the unit when it is fully loaded. To
level your unit, adjust the two leveling legs at
the bottom of the unit.
BEFORE OPERATING
• Locate the unit away from direct sunlight and
sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and
heat sources may increase electrical consumption.
Extreme cold ambient temperatures may also
cause the unit not to perform properly.
• Avoid locating the unit in moist areas.
• Plug the unit into an exclusive, properly
installed-grounded wall outlet. Do not under any
circumstances cut or remove the third (ground)
prong from the power cord. Any questions
concerning power and/or grounding should
be directed toward a certified electrician or an
authorized Products service center.
• After plugging the appliance into a wall outlet,
allow the unit to cool down for 2-3 hours before
placing food in the refrigerator compartment.
REVERSING THE DOOR SWING OF
YOUR APPLIANCE
This refrigerator can be opened either from the left
or right side. The default way of opening the zdoor is
from the right side. If you want to open the door from
the left side, please follow the instructions below.
NOTE: All the removed parts must be well kept for
the re-installation of the door
• Remove the three Screws (6) that hold the Lower
Door Hinge (5), keep the hinge for later use.
• Remove the Door from the Upper Pin (3), and
keep the padded surface upwards to prevent the
scratching
• Remove the Upper Hinge Cover (1), remove the
two Screws (2), hold the Upper Hinge (3), save the
hinge for later use.
• Remove the Hole Cover (1) and transfer it to the
same location on the opposite side.
FIGURE 1 (NORMAL POSITION)
FIGURE 2 (POSITION AFTER DOOR REVERSAL)
1. Upper Hinge Cover
6. Screw
2. Screw
7. Hole Cover
3. Upper Hinge
8. Cabinet
4. Door
9. Pin Cap
5. Lower Door Hinge
• Insert the Lower Door Hinge in the right side, fix
the lower right hinge by tightening all the screws.
• Remove the Pin Cap (9) from the right side of the
upper frame of the door, and then transfer it to the
same location on the opposite side.
• Put the door on the Lower Door Hinge (5), keep the
door level , and then fix the Upper Hinge (3) to the
Door (4) by the screws
• Put on the Upper Hinge Cover (1).
SETTING THE TEMPURATURE CONTROL
• Your unit has only one control for regulating the
temperature in the compartment. The temperature
control is located on the upper right hand side of
the compartment.
• The first time you turn the unit on, set the
temperature control to "6".
• The range of the temperature control is from
position "OFF" to "6". After 24 to 48 hours, adjust
the temperature control to the setting that best
suits your needs.
• To turn the appliance off, turn the temperature
control to "OFF".
NOTE:
1. Turning the temperature control to "OFF" position
stops the cooling cycle but does not shut off the
power to the unit.
2. If the unit is unplugged, has lost power, or is
turned off, you must wait 3 to 5 minutes before
starting the unit. If you attempt to restart before
this time delay, the unit will not start.
2