AMD DIrect SSRFR-24D Manuel de l'utilisateur - Page 6
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} AMD DIrect SSRFR-24D. AMD DIrect SSRFR-24D 9 pages. 15” & 24” refrigerator
Imprimer la page
OPERATING YOUR APPLIANCE
It is recommended that you install the appliance
in a place where the ambient temperature is
between 50°F and 109.4°F (10°C-43°C). If the ambient
temperature is above or below recommended
temperatures, the performance of the unit may
be affected. For example, placing your unit in
extremely cold or hot conditions may cause interior
temperatures to fluctuate. The operating temperature
range may not be reached.
CONTROL PANEL
ON/OFF POWER
To turn the appliance ON or OFF, press and hold the
POWER key
for 5 seconds.
UP
AND DOWN
Press
first, then press
or
button
SET
to increase (warm) or decrease (cool) the set
temperature by 1°C/ 1°F.
Press
again, the temperature is selected and
SET
shows the actual temperature. If no other further
operation in 6 seconds, display will show actual
temperature in the cooler
°F/°C SELECTOR
Selects the temperature display setting in Fahrenheit
or Celsius degrees. To change the temperature from
Fahrenheit to Celsius or from Celsius to Fahrenheit,
press
and
at the same time, then hold for 6
SET
seconds.
SETTING THE TEMPERATURE CONTROL
The temperature you are setting will increase by
one degree each time you press the
key and
will decrease by one degree each time you press
the
key.
The range of temperature control is from 32°F to 50°F.
To view the set temperature at any time, press
the
key. The set temperature will flash in the
SET
display window for 6 seconds. After 6 seconds, the
temperature inside the until will reappear in the
display window.
(The temperature preset at the factory is 36°F)
3
15" & 24" REFRIGERATOR USER MANUAL
BEFORE USING YOUR APPLIANCE
Remove the exterior and interior packing.
Before connecting the appliance to the power
source, let it stand upright for approximately 24
hours. This will reduce the possibility of a malfunction
in the cooling system from handling during
transportation.
Clean the interior surface with lukewarm water using
a soft cloth.
Install the handle on the door if not already attached.
INSTALLATION OF YOUR APPLIANCE
Your outdoor refrigerator has been designed for both
built-in and freestanding applications. When built-in,
your refrigerator door does not require additional air
space for top, side or rear. The front grille must not
be obstructed.
NOTE:
It is recommended that you do not install the
appliance near an oven, radiator or other heating
source, as heat sources may increase electrical
consumption. Do not install in a location where the
temperature will fall below 50°F (10°C). For best
performance, do not install the appliance behind
a cabinet door or block the base grille. Plug the
appliance into an exclusive properly grounded wall
outlet.
SITE PREPARATION
1. Position the unit on a flat, level surface capable
of supporting the entire weight of the unit.
Remember the unit will be significantly heavier
once it is fully loaded.
2. Connect the unit to a Ground Fault Interrupter
(GFI).
3. The unit must be installed according to your local
codes and ordinances.
4. ELECTROCUTION HAZARD!
• Electrical Grounding Required - This appliance
is equipped with a 3-prong (grounding)
polarized plug for your protection against
possible shock hazards.
• NEVER remove the round grounding prong
from the plug.
• NEVER use a 2-prong grounding adapter.
• NEVER use an extension cord to connect
power to the unit.
• Where a 2-prong wall receptacle is
encountered or a longer power cord is
required, contact a qualified electrician to
have it replaced in accordance with applicable
electrical codes.
INSTALLATION
LOCATION OF PARTS
1. Position the unit to allow free air flow through the
front grille.
2. Wipe out inside of the unit with a damp cloth.
INSTALLING THE STAINLESS STEEL HANDLE
To install the handle, follow the instructions below.
Remove the right side gasket.
Take out the screws from the bag in the cabinet. Put
the screws in the holes where the handle is to be
installed.
Align the handle with screws, tighten the screws
using a screwdriver until the handle is both flush
and secured tightly against the door side. (DO NOT
overtighten as this may cause damage to the door
surface).
LEVELING THE UNIT
Position the unit on a flat, level surface capable of
supporting the entire weight of the unit when full. The
unit contains four (4) adjustable leveling legs. Turn the
legs clockwise to raise and counterclockwise to lower.
ELECTRICAL CONNECTION
Put the screws on top of the door where the handle is
to be installed. Align the handle with screws, tighten
the screws using the screwdrivers.
WARNING
Improper use of the grounded plug can result
in the risk of electrical shock. If the power
record is cord is damaged, have it replaced by a
qualified or an authorized service dealer.
4