1100 Energy SBP-1100e Manuel de l'utilisateur - Page 6
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} 1100 Energy SBP-1100e. 1100 Energy SBP-1100e 17 pages. Smart battery power system
Imprimer la page2 | Eleven Hundred Energy Corporation
Turn-on/Wake-up from Hibernation
Hibernation: The SBP-1100e will automatically enter a hibernation state after 30 minutes of non-use (and provided
that no live charging power source is connected). This is done to conserve the stored energy which powers the unit, and
thereby extend the energy-retention shelf-life of the unit.
Press RESET to wake up: To turn on or wake up the unit, press firmly with a fingertip on the small silver dot labeled
'RESET', and release. The RESET dot is located just to the left of the SCROLL button on the LCD control panel on the top
face (hinged lid) of the SBP-1100e. Within 3 seconds, the SBP-1100e will wake up and begin to initialize, flashing mes-
sages on the LCD screen.
If needed, connect power to wake up: An SBP-1100e unit which holds a 50% charge when entering hibernation, and
which has remained in hibernation for a few weeks or less, should be able to be awakened by pressing the RESET dot.
Should the unit become completely exhausted while in hibernation, pressing the RESET dot will not awaken the unit.
In that case, connect a charging power source, such as the SBP AC Power Adapter, item no. SBP-AC-ADAPTER-24VDC-
130W, to the INPUT receptacle on the left side of the SBP-1100e. Be sure the AC Adapter is plugged into a live AC out-
let, and that the adapter power switch is on. Within 3 seconds, the unit should wake up and begin to initialize, flashing
messages on the LCD screen. If not, contact 1100 Energy for assistance.
Press SELECT to view product ID: the initialization process takes, one minute until the LCD display goes blank, except
for a row of grey raster rectangles which may appear dimly on the LCD screen.
After the display goes blank, wait one more minute (or less) for initialization to complete, then press the SELECT button
to see the product identification and software version. The software version should match the software version listed on
the cover of this User Manual.
Press SCROLL to view mode and charge state: Press the SCROLL button to view the state of charge and the operational
mode. The state of charge will appear as text on the top line of the LCD display (e.g. 43%), and in a graphical represen-
tation (e.g. four black blocks for a state of charge from 40% to 49%). The operational mode will appear on the bottom
line of the LCD display, unless the unit is charging, in which case 'Charging' will appear. If the mode is 'Idle', the unit
is ready for use. If the mode is 'Twilight', connect a charging power source as described above, and allow the unit to
charge, at least until the state of charge reaches about 15%. To check whether the unit is ready for use, disconnect or
turn off the charging power, and press SCROLL to check the mode; if the mode is 'Idle', the unit is ready for use. If de-
sired, re-connect (or turn on) the charging power to continue charging. The SBP-1100e does not have to be fully charged
before being put to use powering a load, and the unit may deliver power to the load while continuing charging.
Control Panel Buttons and the LCD Display
If the LCD display does not respond to pressing the SCROLL and SELECT buttons, wait one minute for the condition to
correct itself, and try again. If the display still does not respond, press the RESET dot, then wait two minutes, and try
again.
After pressing the SCROLL or SELECT button, the LCD display will light up and show data for 8 seconds, then blink off.
During the 8 seconds display time, the data is not updated in real time, so if at any time up-to-date data is needed,
press the SCROLL button until the desired data set is displayed.
At any time, status messages may appear which will over-ride the data which would otherwise appear in response to
button presses. Sometimes, a long series of such status messages may appear which may interfere with using button
presses to obtain data. In that case, wait until the status messages have stopped before again pressing buttons.
Master Reset
The master RESET button is located about ¼ inch to the left of the domed 'SCROLL' button. The RESET button is not
domed to prevent it from being activated by accident. The SBP-1100e may be reset at any time by pressing the button.
The process takes about two minutes, and the output power will turn off during the reset, then automatically turn on
when the process is complete.
Battery Charging Using the AC Adapter
If the SBP-1100e Smart Battery Power System is to be charged from an AC power source, connect the AC power adapter
(SBP-AC-ADAPTER-24V-130W) to an AC power source of 100 volts to 240 volts, 50 or 60 Hz.
When the connection is made, the charging status may be viewed on the control panel display on the SBP-1100e (push