American Sportworks 5210 Instructions de montage - Page 3

Parcourez en ligne ou téléchargez le pdf Instructions de montage pour {nom_de_la_catégorie} American Sportworks 5210. American Sportworks 5210 3 pages. 208cc fun kart
Également pour American Sportworks 5210 : Manuel du propriétaire / Manuel des pièces détachées (20 pages)

Imprimer la page

PN 15363R1 page 2 of 2

7 Overhead Cross Bar Installation

• Locate the cross bar, fasteners, and plastic end caps: (1) 15471, (2)

14696, (2) 15114, (2) 14087, and (2) 15475.

• Slip the bar end caps over both ends of the cross bar (shaded) Set the

cross bar in place and install the fasteners with 10mm Socket Wrench.

DO NOT tighten any fasteners at this time.

8 B-Pillar Installation

• Locate the B-Pillars, fasteners, and the plastic end caps: (1) 15472, (1)

15473, (2) 14086, (2) 14696, (6) 15114, (6) 14087, (2) 14088 and (2) 15475.

• Slip the bar end caps over the ends of the B-Pillars that attach to the

A-Pillar. Set the B-Pillars (shaded) in place and install the fasteners with

a 12mm Wrench and 10mm Socket Wrench. The 55mm long fastener

is used at the connection to the main frame and the 50mm long fastener

is used at the connection to the A-Pillar.

DO NOT tighten any fasteners at this time.

Required Hardware

Part #

Description

15546

SEAL, BAR CONNECTION - 1.125"

14086

BOLT, M8 X 1.25 X 55 (Flange Head)

15114

WASHER, BAR CONNECTION M8 X 24 X 1.25

14087

WASHER, CONCAVE CLAMP

14088

NUT, M8 X 1.25 LOCKING (Flange Head)

14696

BOLT, M8 X 1.25 X 50 (Flange Head)

15475

ENDCAP, BAR - 1.125" BLACK PLASTIC

14426

BOLT, M6 X 1.00 X 14 (Flange Head)

14631

COVER, STEERING WHEEL

15113

COVER, BOLT CAP

5210 208cc FUN KART

ASSEMBLY INSTRUCTIONS

9 Spoiler Installation

• Locate the spoiler, fasteners, and plastic end caps: (1) 15479, (2) 14696,

(2) 15114, (2) 14087, and (2) 15475.

• Slip the bar end caps over both ends of the spoiler (shaded) and set the

spoiler in place against the C-Pillar and install the fasteners with 10mm

Socket Wrench.

10 Tighten Fasteners

• Use a 12mm Wrench and 10mm Socket Wrench to tighten all the

fasteners, starting with step 5.

• Install Rubber Fastener Caps on all tightened overhead bar bolts: (20)

15113

11 Safety Flag Installation

• The flag fasteners have been pre-installed onto the right rear corner of

the spoiler.

• Simply loosen the plastic nut from the top side of the rack and slip the

flag into place.

• Finger-tighten the plastic nut to retain the flag.

12 Steering Wheel Installation

• Locate the steering wheel and fasteners: (3) 14426.

• The steering wheel has three mounting holes on it. With the front wheels

aligned in the straight position, orient the steering wheel with one hole at

the 6:00 position, and the other holes at 10:00 & 2:00 positions.

• Using an 8mm Socket Wrench, install the bolts and tighten to secure

the steering wheel

• Align the steering wheel cover and snap into place. (1) 14631.

Quantity

13 Final Preparation

• Fill the fuel tank with clean, fresh mid-grade gasoline.

• Check the engine oil level per the supplied Owner/Operator

manual.

• Refer to the supplied Owner/Operator manual prior to operating

your new Fun Kart.

Orientation of wheel holes