American Standard Bordeaux 9532.495 Instructions d'assemblage et d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Instructions d'assemblage et d'installation pour {nom_de_la_catégorie} American Standard Bordeaux 9532.495. American Standard Bordeaux 9532.495 4 pages. 32" vanity with wood top
Imprimer la pageOptional marble top 9532.495 with Ovalyn 0495 undermount
sink...
Two people recommended for this installation
NOTE: Marble top comes pre-cut for the Ovalyn under counter mount sink and
8" faucet spread. Also it is strongly recommended to seal the marble top after
installation and prior to use.
Remove wood top if not already done.
Mount the drain assembly (not included) on the sink. Be certain to apply a bead
of sealing putty on the underside of the drain (Part "A") in order to ensure a
watertight seal between the sink and drain. Remove excess putty after installing
the drain on the sink.
Turn the marble top upside down and place it on a clean, scratch
resistant surface. Apply a bead of silicone adhesive to the rim of
the sink. Center the sink over the cutout and (secure it to the top
using the mounting kit provided).
NOTE: Brass inserts are preinstalled on the underside of the marble
top. Use the 4 brackets supplied with the sink mounting kit and the 4
screws supplied with the marble top.
Turn the top right-side up and install the faucet per the manufacturer's
instructions.
Apply a bead of silicone adhesive to the rim of the vanity. Place the marble top
centered left to right on the vanity and with the back edge of the top even with the
rear of the vanity. Clean up any excess silicone.
Connect the trap to the drain assembly hand tight to check alignment. It may be
necessary to cut off part of the tailpiece (area "A") or part horizontal leg of the trap
(area "B").
Connect hot and cold supply lines to the shut off valves. Tighten trap joints for
watertight assembly.
Care and Cleaning of Vanity
Dust the vanity frequently with a clean, soft, dry, lint-free cloth, as well as polish it on a regular basis. Clean the surface by rubbing in
the direction of the grain. Use polishes that contain detergents, emulsifiers and mineral oil. Avoid using silicone cleaners and waxes.
Clean up excess water and spills immediately. Use a blotting rather than a wiping action. Water left over a long period of time will
cause white spots in the finish.
NOTE: Please note that some chemicals may damage the finish. Take care to avoid the following: iodine, hair dye, after shave lotion,
shaving cream, alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray Disinfectant®, Dow Disinfectant®, acetone, paint
remover, Formula 409®, Tile-X®, and Nair®.
Care and Cleaning of the Marble Vanity Top
Marble is porous and easily stained. Wipe off anything spilled on it immediately. It should be washed or cleaned regularly with fresh
warm water and a non-abrasive clean cloth. Also, using a non-abrasive, neutral (pH balanced) cleaner will help remove dirt and grime,
but it is recommended to first try warm water only.
Marble should be sealed regularly with a good quality marble sealer. Marble sealers are available at most retail home supply stores.
Follow the instructions on the sealer container for proper application and frequency of use. The sealer acts as a stain inhibitor and
prevents most stains and soil from being absorbed into the porous surface, but it is NOT a guarantee against staining. All spills should
be cleaned immediately. Avoid contact with all oils and petroleum-based products. Also, avoid contact with all acid or caustic products
such as vinegar, citrus or fruit juices, soda, chlorine, and nail polish remover. If the marble is well sealed, the warm water and non-
abrasive cloth should keep it clean.
- 3 -
A
B
A
73 0 5 4 8 - 1 0 0 R e v. B