American Standard 1340M Series Instructions d'installation
Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} American Standard 1340M Series. American Standard 1340M Series 2 pages. Whirlpools
Également pour American Standard 1340M Series : Manuel d'utilisation et d'entretien (6 pages)
Imprimer la page
METERING FAUCET
SINGLE TAP PUSH BUTTON FAUCET
1340 SERIES FOR COLD AND TEMPERED
SUPPLIES
1340M SERIES INCLUDES BELOW DECK
MIXING VALVE WITH STRAINER
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully
before you begin.
WARNING: SUPPLY INLET MUST BE FILTERED WITH A 60 MESH SCREEN.
USE AMERICAN STANDARD MIXING VALVE WITH STRAINER OR COMMERCIAL 60 MESH STRAINER.
GASKET
MIXING
STRAINER
VALVE
FILTER
ASSEMBLY
SCREEN
DUCK
BILL
CHECKS
1
ASSEMBLING ESCUTCHEON KIT (OPTIONAL)
Turn off hot and cold water supplies before beginning.
Peel off paper backing from PADS and stick both
PADS to underside of ESCUTCHEON about 1/4"
from ends.
Peel off paper backing from WASHER and stick
WASHER into circular groove of SUPPORT PLATE.
Place SUPPORT PLATE
of ESCUTCHEON with WASHER visible.
Apply a bead of PUTTY around
the inside of ESCUTCHEON edge.
Turn ESCUTCHEON over and
center it with SUPPORT
PLATE over center hole
of sink deck.
BODY
AERATOR
KEY
ESCUTCHEON KIT
(OPTIONAL)
DECK
WASHER,
BRASS
LOCK-RING
AND SCREWS
RISER TUBE
(NOT INCLUDED)
1340 SERIES
SUPPLY
NUT
1340M SERIES
CAUTION
WASHER
in center
PAD
PUTTY
Installation
Instructions
1340 SERIES
1340M SERIES
2
ASSEMBLING MOUNTING KIT
SET SCREWS
HANDLE
Thread (3) SCREWS into LOCK RING.
SCREWS should extend half-way thru RING.
SPRING
3
MOUNTING FITTING
RETAINING
RING
LEVER
Install faucet through the ESCUTCHEON being sure the
VALVE
rubber GASKET is between the FAUCET and the
CARTRIDGE
ESCUTCHEON.
Install brass WASHER and turn LOCK-RING onto SHANK.
HANDLE
Tighten (3) SCREWS in the LOCK-RING to secure fitting.
RETAINER
FOR 1340 SERIES ONLY
Warning; 60 MESH STRAINER required for supply water.
Install RISER TUBE (not included) and tighten
SUPPLY NUT.
Connect RISER TUBE to COLD or TEMPERED water
supply.
FOR 1340M SERIES
Connect FLEXIBLE FAUCET
SUPPLIES (1/2" faucet cone
on one end, 3/8" compression
on the other) to the MIXING
VALVE INLETS and the
hot/cold wall stops.
The FLEXIBLE FAUCET
SUPPLIES are NOT
included. Turn on WALL
STOPS and check
for leaks.
With WALL STOPS open
and water flowing, adjust
MIXING VALVE to temper
water.
PAD
SUPPORT
PLATE
ESCUTCHEON
PUSH
Certified to comply with ANSI A112.18.1M
U.S. PATENT NOS.
STRAINER
HOT
HOTTER
0 1 2 6 9 2 D
LOCK RING
SCREWS
MIXING
VALVE
MIXING
VALVE
INLETS
MIXING
VALVE
ADJUSTMENT
FLEXIBLE
FAUCET
SUPPLIES
WALL
COLD
STOPS
MIXING
VALVE
COLDER