American Standard TOWN SQUARE 2748 Manuel d'installation - Page 7
Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} American Standard TOWN SQUARE 2748. American Standard TOWN SQUARE 2748 17 pages. American standard bathing pool installation guide
Également pour American Standard TOWN SQUARE 2748 : Fiche technique (2 pages)
Imprimer la page
INSTALLATION AND FRAMING INSTRUCTIONS:
The variety of installations possible for this air massage system may require framing procedures
other than those shown. Locate studs as required. Ensure roughing-in dimensions are proper,
plumb and square. Provisions must be made in all installations for an access opening for servicing
the air blower and controls. It is strongly recommended that an additional opening be provided for
access to the drain components. The apron should not be used as the primary access opening.
1. Position the air massage system into the installation opening and level the deck in both
directions, shimming the integral feet with attached baseboard as necessary. Refer to the Air
Bath Installation Table for nominal installation dimensions. Mark the final position of the
underside of the deck by tracing a line on to the studs (see Figure 1).
. Remove the air massage system and attach a 1 x 4 stringer to the studs, with the top of the
stringer touching the traced line.
The rim of the bath must not support weight.
!
3. Install supplied cable drain components to the air massage system according to the enclosed drain installation
instructions. Before replacing your air bath for final installation, be certain that an opening has been provided in
the sub-floor for the drain. See the roughing-in drawing for suggested opening size (shadowed) and location
dimensions. The drain/overflow of the bath extends below the bottom of the bath. Note that this requires a cutout
in the floor.
4. Replace air massage system and re-shim the integral support feet with attached baseboard, shimming the entire
length of the baseboard as needed. Secure the shims using construction adhesive, silicone or equivalent
materials.
The rim of the bath must not support weight. Any finish material such as tile or wall board must be
!
self-supporting if it contacts the deck of the bath.
AIR BATH INSTALLATION TABLE
DESCRIPTION
A
Nominal tub length recess opening
B
Nominal tub apron support opening
C
Nominal tub width recess opening
D
Nominal tub height opening
E
Nominal tub length cutout
F
Nominal tub width cutout
** USE CUTOUT TEMPLATE PROVIDED FOR 70 MODEL
NOTICE:
DO NOT BUILD THE SURROUNDING STRUCTURE BEFORE RECEIVING YOUR AIR BATH.
STRUCTURE MEASUREMENTS SHOULD BE VERIFIED AGAINST THE ACTUAL AIR BATH
RECEIVED TO ENSURE PROPER FIT.
TYPICAL RECESS INSTALLATION
D
A
NOTE:
FRONT EDGE
OF BATH MUST
BE SUPPORTED
BY STUD WALL OR
AMERICAN STANDARD
APRON KIT
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
AIR BATH MODEL NUMBER
2748
2742
5-3/4"
151mm
71-3/4"
13mm
3-3/4"
1511mm
3-3/4"
1511mm
41-3/4"
1060mm
41-3/4"
1060mm
1"
533mm
0"
50mm
5"
1473mm
70"
177mm
40-1/"
101mm
40-1/4"
10mm
(305 mm)
LEVELING
STRINGERS
4
(610 mm)
ACCESS PANEL MUST BE LOCATED
ON THE SAME SIDE AS THE BLOWER.
ALLOW OPEN FRAMING ON
BLOWER END FOR SERVICE.
2709
3571
**
60-1/4"
1530mm
66-1/4"
35"
mm
35"
36"
14mm
36"
1-1/"
45mm
1"
43mm
1"
67"
170mm
5-1/"
146mm
64-1/"
36-1/"
7mm
34-1/"
76mm
34-1/"
AS DESIRED
CUTOUT
D
1
AS DESIRED
MOUNTING
SURFACE
WATERPROOF
SEALANT
UNLESS AN ACCESS OPENING OF AT LEAST 12" X 24" (305 X 610mm)
IS PROVIDED, WARRANTY SERVICE WILL NOT BE PERFORMED.
7
FIGURE 1
TYPICAL
INSTALLATION
D
TILE
BEAD
STRIP
LEVELING STRINGER
NOTE: Tile bead kit not included
and must be purchased separately.
3572
3573
3574
163mm
7-1/4"
135mm
60"
mm
35"
mm
40-3/4"
14mm
36"
14mm
41-3/4"
43mm
1"
43mm
1"
163mm
70-1/"
171mm
5-1/4"
76mm
34-1/"
76mm
40-1/4"
TYPICAL PIER TYPE INSTALLATION
F
E
CUTOUT
ACCESS PANEL MUST BE LOCATED
BATH
ON THE SAME SIDE AS THE MOTOR.
ALLOW OPEN FRAMING ON PUMP/MOTOR
END FOR SERVICE.
TILE
WALLBOARD
SEALANT
BATH
ADHESIVE
1 x 4 (not for support)
3575
154mm
7-1/4"
135mm
1035mm
41"
1041mm
1060mm
4"
1067mm
43mm
1"
43mm
140mm
70-1/"
171mm
10mm
40-1/"
10mm
1
(305 mm)
4
(610 mm)
754063-100 Rev. B