American Standard TOWN SQUARE 2847 Manuel d'instructions d'installation - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions d'installation pour {nom_de_la_catégorie} American Standard TOWN SQUARE 2847. American Standard TOWN SQUARE 2847 13 pages. 1.28 gpf/4.8 lpf one-piece toilet elongated right height with seat
Également pour American Standard TOWN SQUARE 2847 : Instructions d'installation (4 pages)
Imprimer la page
7
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
8a
Before continuing, determine the type of water supply connection you have from the chart
below and use the appropriate assembly parts required to properly reconnect the water supply.
DO NOT use plumber's putty to seal these fittings.
METAL/COPPER
FLARED TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
9
TOP
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
1" ABOVE
OVERFLOW PIPE
FLOAT
CUP
FILL
VALVE
VALVE
BODY
ADJUSTABLE
HEIGHT
LOCK NUT
CONE WASHER
COUPLING NUT
(HAND TIGHT ONLY)
11
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
!
WARNING:
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the
!
tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing
chlorine (calcium hypochlorite).
METAL FLANGED
METAL SPIRAL
TUBING
TUBING
LOCK NUT
EXISTING
WASHER
EXISTING
COUPLING
NUT
WATER
SHUT-OFF
Use existing
Use existing spiral cone
coupling nut
washer. Fluidmaster
and washer.
cone washer may not
seal completely on
spiral type supply line.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
ARM
REFILL
NIPPLE
TUBE
TANK
LEVER
Fig. 9A
"S"
CLIP
FLUSH
VALVE
WATER LEVEL
ADJUSTMENT
ROD
FLAPPER
SHANK
WASHER
THREADED
SHANK
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
Diagram 1
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
EXISTING
COUPLING
CONE
NUT
WASHER
COUPLING
NUT
WATER
WATER
SHUT-OFF
SHUT-OFF
Captive cone washers
already included. No
additional washers needed.
ADJUSTMENTS
a. Adjust water level. Water level
should be adjusted to level indicated
on tank by adjusting float cup.
See Step 10 for water level adjustment
method.
b. If bowl fails to siphon, an adjustment
may be required with the lift chain.
Simply remove the bead chain from
the retainment clip (see Fig. 9A) and
take up slack on the chain, and
reinsert on lift rod. Make sure the chain
is not too taught.
- 3 -
8b
With correct washers in place (see
Step 8a), tighten COUPLING NUT
1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
10
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30 seconds.
Adjust the water to desired level
by turning WATER LEVEL
ADJUSTMENT ROD and
moving FLOAT CUP up or
down.
7301450-100 Rev. 3 8/19