American Time SiteSync IQ Manuel de démarrage rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide pour {nom_de_la_catégorie} American Time SiteSync IQ. American Time SiteSync IQ 2 pages. Wireless system controller with standard gps & magnetic mount tx antenna
Également pour American Time SiteSync IQ : Démarrage rapide Manuel d'installation (2 pages), Manuel d'installation et d'utilisation (2 pages), Manuel d'installation et d'utilisation (13 pages), Manuel d'installation et d'utilisation (7 pages), Manuel d'installation et d'utilisation (6 pages), Démarrage rapide Manuel d'installation (2 pages), Démarrage rapide Manuel d'installation (2 pages), Démarrage rapide Manuel d'installation (2 pages), Démarrage rapide Manuel d'installation (2 pages), Démarrage rapide Manuel d'installation (2 pages), Démarrage rapide Manuel d'installation (2 pages), Manuel de démarrage rapide (2 pages), Manuel de démarrage rapide (2 pages)

Imprimer la page
American Time SiteSync IQ Manuel de démarrage rapide
QUICK START INSTALLATION GUIDE
1
Unpack the box
1. Remove the components and system controller from the box.
Save the packing materials in case you need them later.
2
Check the components
Your system kit comes with:
• System Controller
• Premium GPS receiver with 50' cable & mounting kit
• Power supply
(B)
• Campus TX antenna kit
(C)
• Installation and Operation Manual
3
Choose your location
• Choose a location for the GPS receiver outside with a clear
view of the sky. The included mounting bracket allows for
mounting on the side of a building or other structure. The
included set of u-bolts can be used to attach the bracket and
GPS receiver to a mast.
Avoid high voltage equipment and excessive roof overhang
when choosing a location.
• Choose a location for your campus TX antenna either
outside or inside at the highest central location in your facility.
The TX antenna must be located at least 4' away from
the system controller
System controller
located high and central
TX Ant signal
out to clocks
GPS signal in
4
Connect cables to the system controller
A.
Connect the GPS antenna to the PREM GPS port.
B.
Connect the System Controller power supply to the POWER
INPUT port.
C.
Connect campus antenna to the TX ANT port. *Lightning
arrestor must be grounded per local electrical code.
Plug 110v cord into power source. Turn the POWER SWITCH on
the back of the system controller to the on position.
Note: If your system controller supports more than one time sync
(A)
option, refer to the SiteSync IQ Installation & Operation Manual
for detailed instructions.
*
See above
To ground
C
B
SITESYNC IQ
5
A
To local
power
(110vac)
WIRELESS CLOCK SYSTEM
®
Use the Setup Wizard
1. Press 1 to start the Setup Wizard
(Page 9 in Installation Manual)
2. Create a 4 digit User Lock or enter 0000 to disable this
O
feature. Press
.
Tip: Record this password.
3. Create a 4 digit Service Lock (for advanced features) or enter
O
0000 to disable this feature. Press
.
Tip: Record this password.
4. Select local time zone by using the
<>
Set Menu LOCAL
Time Zone Code:
05
99=Custom
USCT
<>=Scroll
OK=Accept
USET=Eastern USCT=Central USMT=Mountain USPT=Pacific
Note: There are 40 options to choose from.
8
5. Press
to select automatic DST (Daylight Saving Time) or
0
to disable DST if your location doesn't observe DST.
Press
O
6. Press
1
for 12-hour mode - AM/PM (1:00PM).
Press
2
for 24-hour mode - Military (13:00).
7. To confirm proper set up, press
8
to sync.
• If successful, "GPS Sync Successful" will display
• If not successful, "GPS Sync Failed" will display. Re-try
by pressing
8
again.
8. "Setup Wizard Successfully Completed" will display.
The system controller now shows the correct time and date. You
will no longer be prompted on power-up for setup information.
9. Verify the unit is transmitting. TX should display for about
three seconds every 30 seconds (approximately the top and
bottom of every minute) in the bottom right corner of the
screen.
MON
MAR
10
2014
10:38:06 AM
USCT
American Time
Status=AUTO
MON MAR 14 2016
10:38:06 AM USCT
American Timel
Status=AUTO
GPS=Y
keys. Press
O
.
Note: Screen
will advance
immediately
TX