AmeriFlow F1 Manuel du propriétaire - Page 4

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} AmeriFlow F1. AmeriFlow F1 7 pages. Filterpack systems

Imprimer la page

STEP 3 EASY TAP ADAPTER INSTALLATION

A. Turn off cold water supply to the sink faucet

and relieve pressure by opening the cold

water faucet. (Repair any existing plumb

ing sink leaks before continuing). Follow water

supply from the cold water supply valve, to

ward the sink faucet, until you reach a

coupling nut (may be at the base of the

faucet). Unscrew the coupling nut. Place

rubber washer into the plastic easy tap faucet

adapter and screw adapter onto location of

coupling nut. Hand-tighten, then tighten one

more complete turn with a wrench. Re-attach

the supply line to the adapter with the cou

pling nut. Leave the cold water off.

NOTE:

"Push-In" style fittings are designed for ease of use. Simply push the tubing in until it seats.

Give a tug on it to make sure it is secure. Insert red locking clip between fitting and collar. If you

need to remove the tubing, remove the red locking clip, hold the locking ring collar against the fitting

while pulling out the tubing. No inserts or nuts are used with the "Push-In" style fittings.

FIGURE 2 - FILTER PAK AND FAUCET INSTALLATION

Garbage Disposal

Water Supply

STEP 4 TUBING CONNECTIONS

IMPORTANT:

Fitting manufacturer requires fittings to be re-checked after system reaches

full operating pressure and temperature, Re-tighten and secure as necessary.

It is not recommended to shorten the length of any tubes during installation. This will make future

servicing easier.

A.¼" White Supply Tube on Filter Pac.

Connect the supply (white) tube firmly into the

push-in port on the side of the easy tap

adapter installed on the cold water supply

line.

OPTIONAL:

If self-piercing valve is

used, connect to valve using brass nut, tubing

support, and ferrule, (not included).

8 F1, F2, F3 FILTERPACKS 08/11 8

CAUTION:

1. When tightening easy tap, make sure the

tube to which you are attaching the easy

tap is not twisted. Use two wrenches to

hold existing tube while tightening the easy

tap adapter.

2. Examine existing cone shaped washer on

water supply tube, adjust or replace if dam-

aged or worn (not included).

3. If self-piercing valve is used instead of easy

tap, attach to hard copper tubing only. Do

not over tighten screws (see instructions on

piercing valve package, not included).

EZ Adaptor

hot

cold

Drinking Water

B. Post Filter Connection to Faucet.

Depending on the model, connect the 3/8"

blue tube from either the outlet side of the

post-filter bowl or the outlet fitting from the

10" inline post-filter cartridge to the 3/8"

push-in adapter fitting on the faucet.

STEP 5 SYSTEM START-UP PROCEDURES

Turn your sink cold water supply valve to the on position while leaving the Filter Pac ball valves

in the off position (horizontal, which is perpendicular to the valve). Check for leaks and adjust as

necessary.

A. Slowly turn Filter Pac ball valve to the on

position (blue valve vertical, which is in line with

the valve). As water enters the filter bowls and

makes its way through the filters you will hear

air escaping through the drain. This is normal.

IMPORTANT:

Check carefully for small leaks every few hours for the first few days to assure there

are no leaks. It is wise on any Filter system to inspect for leaks since the system sits unseen un-

derneath your sink and a small leak may not be detected without close inspection. Check for leaks

occasionally thereafter and make adjustments as necessary.

STEP 6 REFRIGERATOR ICEMAKER HOOK UP

A. If there is not an ice-line from the Filter Sys

tem to the refrigerator, you may choose to run

an ice-line so that your ice and water

dispenser will have filtered water.

B. Connect tube (not included) to appropriate

refrigerator connection and to a plastic "T"

Fitting (not included) spliced into the 1/4" blue

tube between the post filter and faucet. It is

recommended to install a ball valve on the

tube to the refrigerator for service and start

up purposes.

STEP 7 RECOMMENDED FILTER SERVICE LIFE

The types of filters listed below vary depending on Filter system style. The manufacturer provides

very high capacity carbon filters and replacement intervals are based on our filters. Other filters

may not have the same capacity as original factory filters and may not last as long. Water conditions

vary greatly by region and can affect filter change intervals. For filter change interval recommenda-

tions, follow the guidelines below. If in doubt, contact the manufacturer.

A. Carbon Pre-filter. These filters should be

changed at least once a year. Changing

these filters is necessary to help insure life

and water quality. Use of high capacity car-

bon block filters is recommended.

REPLACEMENT FILTERS PART NUMBERS & REPLACEMENT FREQUENCY

Filter pak

1 YEAR

model

10 Micron Carbon

.5 Micron Carbon

CB #135-1210

CB05 #135-1210-1

FP1

CB #135-1210

CB05 #135-1210-1

FP2

CB #135-1210

CBLR #135-1310-1

FP3

Open faucet on the sink until the water starts

coming out. Let faucet run to drain for 3 to 5

minutes.

B. Shut off faucet and check for leaks.

IMPORTANT:

Never turn on icemaker

before Filter Pak is full of water to avoid

damaging refrigerator solenoid. If your

refrigerator has a water dispenser in the

door, upon initial start-up you will need

to depress the water supply lever 2 to 3

minutes before the water will dispense.

.................

To order replacement filters or locate a source

in your area call the factory: AmeriFlow™ Water

Systems 602-275-4188.

1 YEAR

Odor Reduction w/ scale inhibitor

10C4Scale #135-3310

F1, F2, F3 FILTERPACKS 08/11 9