AmerTac WESTEK DIY Series Instructions pour l'installation

Parcourez en ligne ou téléchargez le pdf Instructions pour l'installation pour {nom_de_la_catégorie} AmerTac WESTEK DIY Series. AmerTac WESTEK DIY Series 4 pages. Plug-in lighting fixture. led undercabinet lighting

Imprimer la page

DIY Series LED Undercabinet Lighting

Models: CTRO-L12W, CTRO-L16W and CTRO-L22W

FEATURES

Plug-in design for easy installation

Quick and easy linking system

On/Off switch

Slim Line Bar

INCLUDES

CTRO Series Plug-in Light Fixture (12" or 16" or 22")

(1) Power Cord, (1) Linking Cord, Mounting Hardware.

IMPORTANT SAFETY INSTRUCTIONS

For use with 120V, 60Hz electrical power supply only.

WARNING: TO PREVENT OVERHEATING AND ELECTRICAL SHOCK DO NOT INSTALL IN SMALL ENCLOSED SPACES. TO

PREVENT ELECTRICAL SHOCK DO NOT INSTALL IN WET LOCATIONS.

SAVE THESE INSTRUCTIONS

1. Read and understand all of these instructions before installing ﬁ xture.

2. Keep these instructions in a safe place for future reference.

3. Do not mount over sink or stove.

4. WARNING: These products may represent a possible shock or ﬁ re hazard if improperly installed or attached in any way.

Products should be installed in accordance with these instructions, current electrical codes and/or the current National

Electric Code (NEC).

SECTION 1 - PREPARATION FOR INSTALLATION

Tools Needed

Parts of this Light Fixture

12" or 16" or 22" Light Fixture.

Linking Cord

Power Cord with On/Off switch

Mounting Hardware

SECTION 2 - INSTALLATION

Placement of Fixture and Touchless Dimming Controller

Determine location for connecting to nearest 120V receptacle. (Note: before mounting

to cabinet be sure ﬁ xture is within 5' of an electrical outlet, considering path cord will

take to be neatly and securely mounted to cabinet and wall.) If you are not sure about

this installation consult a local licensed electrician or electrical contractor before

proceeding.

Step 1: Locate Mounting Holes: Place brackets on mounting surface and with a pencil

mark the spot where the screws will be located. See Figure 2. Do the same for a multiple

ﬁ xture installation.

Step 2: Drill Holes and Attach Brackets: For mounting into wood cabinets drill 1/16" pilot

holes, 1/2" deep. Caution: Check your cabinet thickness fi rst. Be careful not to drill

through cabinet. For mounting into drywall, drill 3/16" holes for the plastic wall anchors

(not included). Insert the plastic wall anchors into the proper holes and tap them into

place so they are ﬂ ush with the surface of your drywall.

Step 3: Attach Fixtures: Attach ﬁ xture to mounting brackets by snapping into place.

Connect 5' Power Cord to the ﬁ xture. Plug in Power Cord to a 15A circuit grounded

outlet. Light may be turned on or off using the toggle switch built into the cord. Warning:

Do not conceal power supply cord inside a wall, ceiling, soffi t, kitchen cabinet, or similar

permanent structure. Do not run the power supply cord through holes in walls, ceilings or

ﬂ oors.

Use UL listed cable staples (not included) to route Power Cord to bottom of cabinet and

wall for a clean installation.

Interconnecting Multiple Fixtures

WARNING: In multiple fi xture installations do not electrify fi xture group until all electrical

connections have been made and fi xtures have been securely mounted. For the CTRO

DIY Series Undercabinet Light the maximum wattage of linked fi xtures is 100W. The table

below shows wattage and maximum number of bars of all one kind. If various length

bars are used be sure not to exceed the maximum wattage allowed. DO NOT EXCEED

THIS QUANTITY.

INSTRUCTIONS FOR INSTALLATION OF

PLUG-IN LIGHTING FIXTURE

Model #

CTRO-L12W

CTRO-L16W

CTRO-L22W

CTRO Series ﬁ xtures may be interconnected using the Linking Cord supplied with this kit or

by directly connecting each light bar. Linking cords and light bars can only be attached

in one way as each connector has a different end. See Figure 3.

Follow Fixture Installation instructions above. When using the Linking Cord, there should

be some slack in the cord so that the electrical connectors are not stressed in any

way. Use cord clips (not included) to keep cord safely attached to mounting surface.

WARNING: Do not use Linking Cord as a means to turn ﬁ xtures on and off. Do not link

other manufacturer's or other Westek brand ﬁ xtures to this ﬁ xture.

Bar Length

Watts

12"

16"

22"

Step 1

Locate Holes

Step 2

Drill Pilot Holes

Attach brackets

Step 3

Attach ﬁxture(s)

Max No. Linked

CET