AMES Air Gap 500 Series Instructions d'installation
Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} AMES Air Gap 500 Series. AMES Air Gap 500 Series 2 pages.
Air Gap Installation Instructions
Ames Air Gap Drains are designed to collect water that is being discharged by the relief valve, due to
minor check valve fouling and/or line pressure fluctuations.
Note: Air Gap Drains are not designed to collect the full discharge capacity of the relief valve.
Series 400 and 500 Air Gaps
1
Sizes: 2
⁄
" - 10" (65 – 250mm)
2
1. Remove L shape bracket from one side of air gap drain.
2. Remove screw from one side of the splash guard.
3. Slide one half of the splash guard into the groove on the relief
valve body.
4. Slide the other half of the splash guard into the groove on the
relief valve body and reassemble the two parts together.
5. Reattach the L shape brackets long side up into slots in the
splash guard with screws.
6. Push as much of the sensing hose as possible into the air
gap drain funnel to prevent over spray.
Limited Warranty: Ames Fire & Waterworks (the "Company") warrants each product to be free
from defects in material and workmanship under normal usage for a period of one year from the
date of original shipment. In the event of such defects within the warranty period, the Company
will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY
GIVEN BY THE COMPANY WITH RESPECT TO THE PRODUCT. THE COMPANY MAKES NO
OTHER WARRANTIES, EXPRESS OR IMPLIED.
DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and
exclusive remedy for breach of warranty, and the Company shall not be responsible for any
incidental, special or consequential damages, including without limitation, lost profits or the cost
of repairing or replacing other property which is damaged if this product does not work properly,
other costs resulting from labor charges, delays, vandalism, negligence, fouling caused by foreign
material, damage from adverse water conditions, chemical, or any other circumstances over
which the Company has no control. This warranty shall be invalidated by any abuse, misuse,
misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do
not allow the exclusion or limitation of incidental or consequential damages. Therefore the above
limitations may not apply to you. This Limited Warranty gives you specific legal rights, and you
may have other rights that vary from State to State. You should consult applicable state laws to
determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY
IMPLIED WARRANTIES THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
www.amesfirewater.com
Splash
Guard
THE COMPANY HEREBY SPECIFICALLY
Series 4000SS and 5000SS Air Gaps
1
Sizes: 2
⁄
" - 10" (65 – 250mm)
2
Horizontal
1. Remove two of the relief valve capscrews 180° apart.
2. Remove the relief valve hose from fitting below inlet ball valve.
3. From the top of the air gap, thread the relief valve hose down
and out the slot.
1
4. Use
⁄
" - 20 UNC x 1" long stainless steel screws.
4
5. Reconnect relief valve hose to the fitting below the inlet ball
valve (Fig. 1).
Vertical
1. Detach the sensing line from the inlet ball valve and the elbow
on the relief valve.
2. Remove the elbows from the relief valve base.
3. Hang the Air Gap Drain on the body of the relief valve (Fig. 2).
4. Reinstall the elbow into the base of the relief valve to hold the
Air Gap Drain in place.
5. Install the rigid fitting end of the sensing line to the elbow on
the base of the relief valve and the swivel end to the fitting on
the ball valve.
Fig. 1
A Division of Watts Water Technologies, Inc.
IS-A-AirGaps
Fig. 2