Canon 1211B002 - DR 1210C Manuel de démarrage facile

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage facile pour {nom_de_la_catégorie} Canon 1211B002 - DR 1210C. Canon 1211B002 - DR 1210C 2 pages. Document scanner

Imprimer la page
Canon 1211B002 - DR 1210C Manuel de démarrage facile
Document Scanner DR-1210C
Document Scanner DR-1210C
Easy Start Guide
Easy Start Guide
Thank you for purchasing the Canon DR-1210C Document Scanner. This Easy
Start Guide describes the procedure for setting up the scanner for use. Follow
the procedures outlined in this Easy Start Guide to set up the scanner. Details on
using the scanner are described in the User's Guide packaged with the scanner.
Before you use the scanner, make sure to thoroughly read the User's Guide.
Step 1. Checking the Packing List
When you unpack your scanner, make sure that it contains all of the following
accessories. If any of the items listed below are missing or damaged, contact
your local authorized Canon dealer or service representative.
USB cable
DR-1210C scanner
Easy Start Guide
User's Guide
(this document)
Adobe Acrobat
Warranty Card
Setup Disc
(U.S.A. and Canada only)
(U.S.A. and Canada only)
Note
●
The DR-1210C Setup Disc contains the "DR-1210C Scanner Driver",
"CapturePerfect 3.0", and "OmniPage SE 4", made by Nuance Communications Inc.,
and "Presto! BizCard 5 SE", made by NewSoft Technology Corp.
☞
User's Guide p.17 "About the Setup Disc"
●
Items included in this package are subject to change without notice.
●
You must keep the machine's packaging and packing materials for storing or
transporting the machine.
Step 2. Removing the Packing Materials
and Removing the Transport
Locks
Remove the scanner from the box, take it out of the plastic bag and release the
lock switch on the bottom of the unit. Remove the orange tape and protective
sheets from the scanner.
1.
Peel off the orange tape on the operation panel and press the lock
switch to
(Unlock) position.
Unlock
Lock
Lock Switch
■ Trademarks
• Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also
be trademarks or registered trademarks in other countries.
• Microsoft Windows
®
is a registered trademark of Microsoft USA in the United States and other countries.
• Other brands and product names used in this manual may be trademarks or registered trademarks of
their respective companies.
PUB. CE-IE-489
©2006 CANON ELECTRONICS INC.
2.
Peel off the tape holding the center of the document feed tray and
then remove all of the tape (indicated by ▼ ).
3.
Peel off the orange tape fastening the document feed tray ( 1 ) and
open the document feed tray.
4.
Open the feeder cover ( 1 ), and move the paper release lever in
the direction indicated by the arrow on the lever ( 2 ).
AC adapter
DR-1210C
Setup Disc
Registration Card
5.
Remove the protective sheet.
6.
Return the paper release lever to its original position ( 1 ), and
gently close the feeder cover until it clicks into place ( 2 ).
7.
Carefully close the document feed tray.
8.
Open the feeder and remove the protective sheet (indicated by ▼ ).
*CE-IE-489*
Document
Feed Tray
Step 3. Installing the Software
Install the software before connecting the scanner to the computer.
Feeder Cover
❏
❏
Paper Release Lever
9.
Carefully close the feeder.
CAUTION
●
Close the feeder gently to avoid catching your fingers, as this
may result in personal injury.
●
Do not use excessive force when closing the feeder, as this may
damage or break the glass, and may result in personal injury.
Warning
Be sure to log on with administrator privileges when logging on to Windows.
Close all other applications before installing the software.
1.
Turn ON your computer.
Warning
Do not connect the scanner to the
computer before installing the software.
If you connect the scanner and turn it
ON before you install the software, the
wizard screen on the right will appear.
If this wizard is displayed, click the
[Cancel] button to exit the screen, and
turn the scanner OFF.
Wizard screen (Windows 2000)
2.
Insert the DR-1210C Setup Disc
into the PC's CD-ROM drive.
The setup wizard automatically starts
up when you insert the CD-ROM into
the CD-ROM drive. If the setup
wizard does not start up, execute
setup.exe in the CD-ROM.
3.
Click [Typical Installation].
If you click [Typical Installation], all of
the software is installed. If you want
to select which parts of the software
to install, click [Custom Installation].
4.
Click [Install].
All of the currently displayed
software is installed. To install only
selected software, click [Back] and
select [Custom Installation].
5.
Click [Next].
☞
Continued on back side