Flying Industry Development 0020080 Manuel rapide - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel rapide pour {nom_de_la_catégorie} Flying Industry Development 0020080. Flying Industry Development 0020080 3 pages. Rf wireless transmitter & receiver kit

Imprimer la page
If you want to control a AC 380V motor, you can connect the receiver, the 380V contactor, the 380V motor and the 380V power according following
circuit diagram, then you use the transmitter to control the AC 380V motor.
Setting different control modes:
We have set the receiver as Interlocking control mode before delivery. If you want to use other control modes, do as following operation:
1) Setting Interlocking mode: Turn on the dip switch 1, and turn off the dip switch 2.
Mode Interlocking (working with transmitter CG-3 or CB-3-2): Press -> On; Press another button -> Off.
▼
Press button
of the transmitter: The relay 1 is deactivated, and the contactor 1 is connected, the 380V motor rotates in the positive direction.
■
Press button
of the transmitter: The relay 1 is deactivated, and the contactor 1 is disconnected, the 380V motor stops.
▲
Press button
of the transmitter: The relay 2 is activated, and the contactor 2 is connected, the 380V motor rotates in the reversal direction.
■
Press button
of the transmitter: The relay 2 is deactivated, and the contactor 2 is disconnected, the 380V motor stops.
2) Setting Momentary mode: Turn off the dip switch 1 and 2.
Mode Momentary (working with transmitter CG-3 or CB-3-2): Press and hold -> On; Release -> Off.
▼
Press and hold button
of the transmitter: The relay 1 is deactivated, and the contactor 1 is connected, the 380V motor rotates in the positive
direction.
▼
Release button
: The relay 1 is deactivated, and the contactor 1 is disconnected, the 380V motor stops.
▲
Press and hold button
of the transmitter: The relay 2 is activated, and the contactor 2 is connected, the 380V motor rotates in the reversal
direction.
▲
Release button
: The relay 2 is deactivated, and the contactor 2 is disconnected, the 380V motor stops.
Manual buttons:
▼
Press manual button
of the receiver: The relay 1 is deactivated, and the contactor 1 is connected, the 380V motor rotates in the positive
direction.
■
Press manual button
of the receiver: The relay 1 is deactivated, and the contactor 1 is disconnected, the 380V motor stops.
▲
Press manual button
of the receiver: The relay 2 is activated, and the contactor 2 is connected, the 380V motor rotates in the reversal direction.
■
Press manual button
of the receiver: The relay 2 is deactivated, and the contactor 2 is disconnected, the 380V motor stops.
How to pair the transmitter to the receiver:
1) Press the learning button of the receiver, signal LED on the receiver is on, The receiver enters into status of LEARNING.
2) Press any button on transmitter within 5 seconds, if signal LED flashes 2 times then turns off, it means learning is successful.
3) The receiver can learn several transmitters with different codes.
Delete all transmitters:
We have learned the transmitter to the receiver. If you don't want the receiver to work with the transmitter, you can delete all codes of the transmitters
which are stored in the receiver.
Operation: Pressing the learning buttons of the receiver for 6~7 seconds until the signal LED on the receiver flashes 3 times, then release the
learning button. That means all stored codes have been deleted successfully.
SHENZHEN FLYING INDUSTRY DEVELOPMENT CO.,LTD
http://www.carymart.com