Astrolux EC01 Manuel de l'utilisateur

Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Astrolux EC01. Astrolux EC01 4 pages.

Imprimer la page

The EC01 uses Andúril Firmware

ASTROLUX EC01

User Manual

-1-

Safety precautions

•

Use only reputable 21700 cells of known origin.

•

Remove and recharge the cell when the low

voltage indication is given by the Lamp (repeated

step-downs in light level and eventual shutdown of

the light).

•

The extraordinary energy density that 21700 cells

offers also means that hazardous conditions are

created when a cell is short-circuited or damaged.

Always treat cells with respect and properly

dispose of damaged cells.

•

The EC01 is a very high-intensity flashlight. Do not

point directly at a person, animal, moving vehicles

or flammable materials.

•

When running at higher output levels the head of

the Lamp will quickly heat. This is normal. In

warmer ambient conditions this

temperature may

exceed 50ºC depending on your settings, so please

take the necessary precautions when handling the

Lamp.

Quick start

•

Use one 21700 cell.

•

Unscrew the head and insert the battery. Take care

with the polarity: Plus points toward the head.

•

Screw the head back.

The EC01 blinks once to

confirm it has power and is now operational.

Tighten the head. Do not over-tighten.

•

All functions are performed using the electronic

side switch. And basic usage is very simple: Click

for on/off, hold to change brightness.

Release and

hold again to change brightness the other way.

•

From OFF, hold the button. The light output will

ramp up from a very low level to Ceiling-Of-The-

Ramp. Release the button when the required light

level is reached. (The full ramp takes about

Use a single-click at any time to turn the EC01 OFF.

Please see below for further details.

•

While ramping it does subtle blinks to signal: Max

regulated level (1x7135) and CEILING.

•

The EC01 has two different ramps: SMOOTH RAMP

and STEPPED RAMP. You can change between

them when the lamp is ON with three clicks.

ramp has its own individual settings – for floor

-2-

(lowest level), ceiling (highest level). And the

stepped ramp can also have a configurable number

of steps.

•

TURBO

is only for short times. At around a minute

you may notice it dims slowly down! The user

should use it only for short periods instead of

relying on thermal regulation to prevent heat

damage. Full turbo is powerful enough to start fires

in just a few seconds, especially when aimed at

dark-colored

materials.

Integrated charger

The EC01 has a USB-C charging port. Please use a

premium cable and a power adapter with 5V, 2A to

charge your lamp.

While charging the switch LED is red. It goes green

when charging is finished. .

While charging you can use BattCheck mode from the

Group 1 Blinkies to check the voltage level and all other

flashlight functions can be used normally when

charging.

s.)

Each

-3-

Specifications

A 21700 CREE LED lamp with side switch and a great,

easy user interface.

Emitter: CREE XHP50.2(3V) LED on a copper DTP MCPCB

Lens:

High transmittance glass

Flux:

~3500 lm

Throw:

~298 m

Firmware: The EC01 uses free software called Andúril,

distributed under the terms of the GPL v3.

Code is available from

http://tiny.cc/TKAnduril

User interfaces: [1] By default the EC01 is set to use

SMOOTH RAMPING. Instant access to

TURBO mode is also provided.

[2]

A more conventional STEPPED

RAMPING UI is available if you like discrete

modes level. You can choose how many

steps you want.

[3] MOMENTARY mode is useful for

signaling purposes or rapidly/briefly

lighting up targets. To exit this mode,

physically disconnect power

[4] MUGGLE mode uses a reduced output.

[5] It has an electronic LOCKOUT for safety,

but acts also as momentary low light.

Other functions: Battery check, sunset, beacon,

tactical strobe, party strobe, bike flasher,

candlelight, lightning storm

Battery: one premium 21700 cells. Unprotected cells

are recommended.

Charging:

Integrated charger via USB-C

Driver: FET+1 driver. Low parasitic drain while OFF

Body: Aluminum with HA III anodizing

Switch: Electronic side switch

Ingress rating: Equivalent to IPX8

Weight:

Approximately 119 g without cells

Size:

37 mm Ø head x 120 mm length.

Manual design and concept by J. Hollmann.

Content from budgetlightforum, collected over time.

Many thanks to ToyKeeper for her great software!

Rev. A

-4-