Canyon 98-161 Manuel d'instructions de montage - Page 8
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions de montage pour {nom_de_la_catégorie} Canyon 98-161. Canyon 98-161 14 pages. Cottage colors collection bunk bed
Imprimer la page
LIST OF CONTENTS
COTTAGE COLORS COLLECTION
BUNK BED END BOX ( 98-706 ) FIG.1 ( 2 PCS )
A.- (1) HEADBOARD
6 PCS SIDE RAILS BOX ( 98-730 ) FIG.2
B.- (4) SIDE RAILS
C.-(2) GUARD RAILS
HARDWARE PACK
D.- (24) 80MM FLAT HEAD BOLTS
E.- (24) 5/8" CROSS DOWEL NUTS
F.- (1) 5MM ALLEN WRENCH
4 PCS SLAT PACK BOX ( 98-645 ) FIG.3 ( 2 PCS )
G.- (4) SLATS
HARDWARE PACK
H.- (8) 1 1/4" SCREWS
LADDER BOX ( 98-720 ) FIG.4
I.- (1) LADDER
HARDWARE PACK
J.- (2) METAL HOOK BRACKETS
K.- (6) 1" SCREWS
TRUNDLE BED STORAGE BOX ( 98-744 ) FIG.5
L.- (1) TRUNDLE BED
1.- TO ASEMBLE TWIN OVER TWIN BUNK BED, USING TWO HEADBOARDS (A), FOUR SIDE RAILS (B), AND TWO GUARD RAILS (C).
2.- INSERT TWO CROSS DOWELS (E) IN ACCESS HOLE INSIDE THE SIDE RAIL&GUARD RAIL, ALIGN THE CROSS DOWEL NUT, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.6
3.- ATTACH TWO SIDE RAILS (B), AND TWO GUARD RAILS (C) ON TOP HEADBOARDS WITH THE GROVE LINES AS SHOWN IN FIG.7, INSERTING TWO 80MM FLAT HEAD BOLTS (D) INTO TOP HEADBOARD HOLES,USE 5MM
ALLEN WRENCH (F) TO TIGHTEN BOTH FLAT HEAD BOLTS
FOUR CORNERS.
4.- TO ATTACH BOTTOM SIDE RAILS, USE THE SAME PROCESS AS SHOWN IN TOP SIDE RAILS, USING TWO SIDE RAILS TO HEADBOARD BOTTOM HOLES, SEE FIG.7
5.- PLACE FOUR SLATS (G) ON TOP & BOTTOM SIDE RAIL CLEATS, ONE SLAT IN BOTH HEADBOARD ENDS, PUSH THE SLATS AGAINST THE BED END POST (FIG. A) AND TWO SLATS IN THE MIDDLE AT EQUAL DISTANCE
FROM THE END SLATS, THEN EACH SLAT MUST BE FASTEN WITH ONE 1 1/4" SCREW (H), SEE FIG.8
6.- SLIDE TRUNDLE BED (L) UNDER BOTTOM SIDE RAILS,
YES,
HORIZONTAL GROOVE
FIG. 6
REV 01 02/08/16
TWIN BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 1
(HPK00104)
(HPK00016)
(HPK00008)
TWIN BUNK BED ASSEMBLY
( DO NOT TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER )
AS SHOWN IN CONFIGURATION #1 )
NO
FIG. 7
CANYON FURNITURE COMPANY.
A
FIG. 1
G
H
FIG. 3
K
FIG. 4
( USE TWO 4 PCS SLAT PACK 98-645 )
( USE TWO 4 PCS SLAT PACK (98-645) AS SHOWN IN CONFIGURATION #1 )
FIG. 8
PAGE 2 OF 5
B
D
J
I
SEE FIG.7, REPEAT THE SAME PROCESS AT ALL
C
F
E
FIG. 2
L
FIG. 5
FIG. A
KIS01130