Electrex EXA 96 Manuel d'installation

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} Electrex EXA 96. Electrex EXA 96 4 pages.
Également pour Electrex EXA 96 : Manuel d'installation (4 pages)

Imprimer la page

96 RS485

INSTALLATION GUIDE

It is forbidden to duplicate, adapt, transcript this document without Akse written

authorization, except when regulated accordingly by the Copyright Laws.

WARRANTY

This product is covered by a warranty against material and manufacturing defects for a 24

months period from the manufacturing date.

The warranty does not cover the defects that are due to:

• Negligent and improper use

• Failures caused by atmospheric hazards

• Acts of vandalism

• Wear out of materials

• Firmware upgrades

Akse reserves the right, at its discretion, to repair or substitute the faulty products

The warranty is not applicable to the products that will result defective in consequence of

a negligent and improper use or an operating procedure not contemplated in this manual.

RETURN AND REPAIR FORMALITIES

Akse accepts the return of instruments for repair only when authorized in advance. The

transport costs are at customer charge.

RE-SHIPPING OF REPAIRED PRODUCT

The terms for re-shipment of repaired products are ex-works, i.e. the transport costs are

at customer charge.

Products returned as detective but found to be perfectly working by our laboratories, will

be charged a ﬂ at fee to account for checking and testing time irrespective of the warranty

terms.

SAFETY

This instrument was manufactured and tested in compliance with IEC 61010-1 CAT III -

300V class 2 standards for operating voltages up to 300 VAC rms phase to neutral.

In order to maintain this condition and to ensure safe operation, the user must comply with

the indications and markings contained in the following instructions:

• When the instrument is received, before starting its installation, check that it is

intact and no damage occurred during transport.

• Before mounting, ensure that the instrument operating voltages and the mains

voltage are compatible then proceed with the installation.

• The instrument power supply needs no earth connection.

• The instrument is not equipped with a power supply fuse; a suitable external

protection fuse must be foreseen by the contractor.

• Maintenance and/or repair must be carried out only by qualiﬁ ed, authorized

personnel

• If there is ever the suspicion that safe operation is no longer possible, the instrument

must be taken out of service and precautions taken against its accidental use.

Operation is no longer safe when:

•

There is clearly visible damaged.

•

The instrument no longer functions.

•

After lengthy storage in unfavorable conditions.

•

After serious damage occurred during transport

The instruments must be installed in respect of all the local regulations.

OPERATOR SAFETY

Warning: Failure to observe the following instructions may lead to a serious danger of

death.

• During normal operation dangerous voltages can occur on instrument terminals and

on voltage and current transformers. Energized voltage and current transformers

may generate lethal voltages. Follow carefully the standard safety precautions while

carrying out any installation or service operation.

• The terminals of the instrument must not be accessible by the user after the installation.

The user should only be allowed to access the instrument front panel where the

display is located.

• Do not use the digital outputs for protection functions nor for power limitation functions.

The instrument is suitable only for secondary protection functions.

• The instrument must be protected by a breaking device capable of interrupting both

the power supply and the measurement terminals. It must be easily reachable by the

operator and well identiﬁ ed as instrument cut-oﬀ device.

• The instrument and its connections must be carefully protected against short-circuit.

Precautions: Failure to respect the following instructions may irreversibly damage to the

instrument.

• The outputs and the options operate at low voltage level; they cannot be powered by

any unspeciﬁ ed external voltage.

• The application of currents not compatible with the current inputs levels will damage

to the instrument.

Further documentation may be downloaded from our web site www.electrex.it.

This document is owned by company AKSE that reserves all rights.

DECLARATION OF CONFORMITY

Akse hereby declares that its range of products complies with the following directives EMC

2014/30/EU, 2014/35/EU

and complies with the following product's standard CEI EN

61326 - Ed. 2.0 (2012) – IEC 61326 - Ed. 2.0 (2012)

61010 Ed. 3 (2010). The product has been tested in the typical wiring conﬁ guration and

with peripherals conforming to the EMC directive and the LV directive.

CEI EN 61010 Ed. 3 (2010) – IEC

READINGS

EXA 96

PRODUCT CODE

PFAXXXX-XX-X

VERSION

X.XX XXXX

SERIAL

XXXXXX

ADDRESS

027

P/PF

CNT

ESC

ENTER

MEASURE LIST TABLE

(The parameters available vary according to instrument conﬁ guration)

P/PF

CNT

ULN

Ea + MAIN Er + L MAIN Es + MAIN

ULL

I ∑

P ∑

Ea - MAIN

ULN THD I THD

P AVG +

Ea + Fase

ULL THD

I MAX

P AVG -

Ea - Fase

ULN MIN

I AVG

P MD +

Ea + P1

ULL MIN

I MD

PMD -

Ea - P1

ULN MAX

Ea + P2

ULL MAX

Q ∑

Ea - P2

Q AVG +

Ea + P3

Q AVG -

Ea - P3

Q MD +

Q MD -

S ∑

S AVG +

S AVG -

S MD +

S MD -

PF ∑

LEGEND OF PARAMETERS AND SYMBOLS

Voltage

Phase Neutral

Phase Phase

Current

Neutral current

Active Power

Reactive Power

Apparent Power

Power Factor

Frequency

Active Energy

Reactive Energy

Apparent Energy

MECHANICAL CHARACTERISTICS

Case

Self-extinguishing plastic material class V0

Protection degree

IP40 on front panel, IP20 terminals side

Size

96 x 96 x 72 mm

VOLTAGE INPUTS

Direct insertion

Up to 300 Vrms phase-neutral or 520 Vrms phase to phase

With external VT:

Primary: programmable (max. 400 kV)

Secondary: programmable (max. 300 V)

Overload: 900 Vrms phase to phase for 1 sec

Aux. power supply

230/240Vac +/- 10% 50/60Hz

Self consumption:

< 2,5VA

MODELS

PFAEC11-62-B

Keep pressed for 2 seconds to display:

- Type of instrument

- Firmware version

- Serial number

- RS485 address

C1 MAIN

Er - L MAIN

Es - MAIN

C2 MAIN

Er + C MAIN Es + Fase

C3 MAIN

Er - C MAIN Es - Fase

C4 MAIN

Er + L Fase

Es + P1

C1 P1

Er - L Fase

Es - P1

C2 P1

Er + C Fase

Es + P2

C3 P1

Er - C Fase

Es - P2

C4 P1

Er + L P1

Es + P3

C1 P2

Er - L P1

Es - P3

C2 P2

Er + C P1

C3 P2

Er - C P1

C4 P2

Er + L P2

C1 P3

Er - L P2

C2 P3

Er + C P2

C3 P3

Er - C P2

C4 P3

Er + L P3

Er - L P3

Er + C P3

Er - C P3

THD

Total Harmonic Distortion

AVG

Average (rolling) value

Maximum Demand

MIN

Minimum values (10 cycles time base)

MAX

Maximum values (10 cycles time base)

Imported value

Exported value

Er L

Inductive

Er C

Capacitive

Time counter

Pulse count

MAIN

Total

P1,P2,P3 Partial 1,2,3

LIFE

Device lifetime

t MAIN

t P1

t P2

t P3

t LIFE