AMPHORA Ready Instructions de montage - Page 2

Parcourez en ligne ou téléchargez le pdf Instructions de montage pour {nom_de_la_catégorie} AMPHORA Ready. AMPHORA Ready 4 pages.

Imprimer la page

10)

Place the front arch on the front plate of the bottom.

Then bolt the smoke guard to the arch. Do not

tighten the joints too firmly, otherwise the damage of the

refractory shapes may occur due to heat dilatation.

15)

Cover the assembled arch with at least 1 layer of

aluminium foil I8. Place the isolation bio-mat on the

aluminium foil according to the cutting plan for the

bio-mat. Make sure the bio-mat doesn't get distorted

during the application.

19)

11)

Place the rear arch

and rear arch. Side arches should be placed with a hole

on the rear plate of the bottom.

16)

Place the front parts T9 and T10 of the body to

the stand above the front arch (push the

front edge of the body to the portal as

much as possible). Before you connect

the two parts, apply adequate

a hole for the thermometer. Main-

tain a dilatational interstice at least 3

mm between the upper edge of the front

arch and the front part of the body. For this

purpose place the supplied dilatation pads under the

side edges. If you use more than 2 pieces of pads on top of

each other, bind them together using silicone caulk. (A purpose of the silicone

caulk application between the two front parts is to connect them so that they

don't spread and also as a protection against water if you don't follow the

warranty conditions to place the oven under a roof.)

Apply silicone caulk between the body parts and along

oven circumference between the bottom edge of the

body and the stand - into the formed joint, the used

dilatation pads should also get fixed. Silicone the

chinks in the way the silicone caulk could be

removed in the case of necessity of disas-

sembling the oven (e.g. in the case of a

warranty claim).

A purpose of this silicone caulk application is

to prevent water to get into the oven in the case

you don't follow the warranty conditions to place

the oven under a roof. If you follow the conditions, it's

enough to fix the dilatation pads.

12)

Place the small side arch between the front

towards the front portal.

17)

amount of silicone caulk into the

locks and on the whole

surface between the parts.

Make sure the caulk don't fill

Place the rear body to the

stand above the rear arch.

20)

13)

Place the central part of the arch with a hole

towards the chimney. Shape should be placed

on the top of the arch.

18)

possible. If it is necessary to align the parts, place the supplied dilatation

pads under the side edges, preferably at places marked by arrows (9

points). Do not remove the pads. If you use more than 2 pieces of pads on

top of each other, bind them together using silicone caulk.

Cut out a hole for the chimney (through insulation and the aluminium foil). Place the rope seal

into the opening in the front body into the prepared groove in the inner front arch to create

two threads of rope seal. Insert carefully the chimney base until the cover flange sits

properly on the oven body. You can check with your hand from inside of the chimney if

the rope doesn't get distorted while inserting the chimney base (if the rope gets

damaged, heat and smoke can get into the space between the inner shapes

and the body). Turn the dumper always lightly, not more than 90 degrees.

Otherwise the thread may turn and the sign "open, closed" may not corre-

spond with an actual position. Preferably don't pull out the chimney base

out of the oven very often otherwise the rope seal may get damaged. When

attaching chimney which is longer than half a meter, make sure that chimney

system is not exerting excessive pressure on the body. Close the oven with steel door.

Last, place the thermometer into the opening behind the chimney (for proper mounting it

14)

Place the last two shaped pieces

into the remaining space so that the locks match.

Place the central

part of the body on the

stand between individual

parts of the body so that the

cutouts of individual shaped pieces

match and joints are as narrow as

is necessary to pierce through the insulation).