AMPHORA Plus Instructions de montage - Page 2

Parcourez en ligne ou téléchargez le pdf Instructions de montage pour {nom_de_la_catégorie} AMPHORA Plus. AMPHORA Plus 2 pages.

Imprimer la page

Place the front arch on the front plate of the bottom.

Then bolt the smoke guard to the arch. Do not

tighten the joints too firmly, otherwise the damage of the

refractory shapes may occur due to heat dilatation.

Cover the assembled arch with at least 1 layer of

aluminium foil I8. Place the isolation bio-mat on the

aluminium foil according to the cutting plan for the

bio-mat. Make sure the bio-mat doesn't get distorted

during the application.

13)

Place the rear arch

and rear arch. Side arches should be placed with a hole

on the rear plate of the bottom.

10)

Place the front parts T9 and T10 of the body to

the stand above the front arch (push the

front edge of the body to the portal as

much

connect the two parts, apply

sure the caulk don't fill a hole for

the thermometer. Maintain a dilata-

tional interstice at least 3 mm between the

upper edge of the front arch and the front part of

the body. For this purpose place the supplied dilatation

pads under the side edges. If you use more than 2 pieces of

pads on top of each other, bind them together using silicone caulk. (A purpose of

the silicone caulk application between the two front parts is to connect them so

that they don't spread and also as a protection against water if you don't follow

the warranty conditions to place the oven under a roof.)

Apply silicone caulk between the body parts and along

oven circumference between the bottom edge of the

body and the stand - into the formed joint, the

used dilatation pads should also get fixed.

Silicone the chinks in the way the silicone

caulk could be removed in the case of

necessity of disassembling the oven (e.g.

in the case of a warranty claim).

A purpose of this silicone caulk application

is to prevent water to get into the oven in the

case you don't follow the warranty conditions to

place the oven under a roof. If you follow the condi-

tions, it's enough to fix the dilatation pads.

Place the small side arch between the front

towards the front portal.

11)

possible).

Before

you

adequate amount of silicone

caulk into the locks and on

the

whole

surface

between the parts. Make

Place the rear body to the

stand above the rear arch.

14)

Place the central part of the arch with a hole

towards the chimney. Shape should be placed

on the top of the arch.

12)

as narrow as possible. If it is necessary to align the parts, place the supplied

dilatation pads under the side edges, preferably at places marked by arrows

(9 points). Do not remove the pads. If you use more than 2 pieces of pads

on top of each other, bind them together using silicone caulk.

Cut out a hole for the chimney (through insulation and the aluminium foil). Place the rope

seal into the opening in the front body into the prepared groove in the inner front arch

to create two threads of rope seal. Insert carefully the chimney base until the

cover flange sits properly on the oven body. You can check with your hand from

inside of the chimney if the rope doesn't get distorted while inserting the

chimney base (if the rope gets damaged, heat and smoke can get into the

space between the inner shapes and the body). Turn the dumper

always lightly, not more than 90 degrees. Otherwise the thread

may turn and the sign "open, closed" may not correspond with an

actual position. Preferably don't pull out the chimney base out of the

oven very often otherwise the rope seal may get damaged. When attaching

chimney which is longer than half a meter, make sure that chimney system is not

exerting excessive pressure on the body. Close the oven with steel door. Last, place

the thermometer into the opening behind the chimney (for proper mounting it is necessary

Place the last two shaped pieces

into the remaining space so that the locks match.

Place the central part

of the body on the stand

between individual parts of the

body so that the cutouts of individu-

al shaped pieces match and joints are

to pierce through the insulation).