DPLUS CLIMA24 Manuel - Page 9

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} DPLUS CLIMA24. DPLUS CLIMA24 16 pages.

Automatic setting of the stroke with leaves delay and slowing down spaces fix

PROGRAMMING can be performed only with the presence of mechanical stops in Opening and Closing.

Instruction for a 2 leaves swing gate; in case of 1 single swing leaf (dip 1 SW1 ON) the instruction regards only the motor M1.

1) Place the leaves half way opening; keep pressed the button LEARN. until both operators will start closing (approx. 10 seconds).

2) The control panel closes the leaves until they touch the mechanical stoppers.

3) M1 starts opening and after 3 seconds M2 starts opening too.

4) Both operators will stop automatically at the mechanical stoppers in opening.

5) Then, the control panel will close the leaves finishing with a slowing down before touching the mechanical stoppers in closing.

6) The control panel automatically goes out from the setting and it is ready to work.

In the automatic setting, the delay between the 2 leaves is 3 seconds both in opening and closing and the slowing down is approx. 4 seconds before

reaching the mechanical stoppers.

WARNING: In case of re‐adjustment of the trimmer RALL. or VELOC. it is ABSOLUTELY necessary to repeat the setting.

11a

Manual setting of the stroke with leaves delay and slowing down spaces customized

PROGRAMMING can be performed only with the presence of mechanical stops in Opening and Closing.

AMP trimmer adjusts the leaf strength ; the greater the force (+), the greater the effort required to stop the gate.

VELOC trimmer adjusts the speed during the ride.

RALL trimmer adjusts the slowdown speed.

Warning: to exclude deceleration, place RALL trimmer at max (towards +)

Following instruction are for a 2 leaves swing gate; in case of 1 single swing leaf (dip 1 SW1 ON) the instruction regards only the motor M1.

1) Close the gate and press once button LEARN; led DL6 starts flashing.

2) Press once button WORK; M1 leaf starts opening.

3) As soon as M1 leaf has reached the position you want to set the slowing down, press again the button WORK, the leaf will start the slowing down

procedure.

4) After that, M1 leaf will hit the mechanical stopper in opening and automatically will stop.

***** ATTENTION: MECHANICAL STOP necessary and mandatory !!!!! *********

(If it is not possible to install the mechanical stop and the motor, once reached the end of the run, continues pushing: after 2‐3 seconds press

and release the button WORK ; the motor stops).

5) Press again and release button WORK to start counting the delay of the leaves in opening; Led DL6 flashes fast.

6) Press again button WORK to stop the counting for the time to apply to the delay in opening. Automatically M2 leaf starts opening.

7) When M2 leaf has reached the position you want to set the slowing down, press again button WORK, the leaf will start the slowing down

procedure.

8) After that, M2 leaf will hit the mechanical stopper in opening and automatically will stop

***** ATTENTION: MECHANICAL STOP necessary and mandatory !!!!! *********

(If it is not possible to install the mechanical stop and the motor, once reached the end of the run, continues pushing: after 2‐3 seconds press

and release the button WORK ; the motor stops).

9) Press once again the button WORK. Leaf with M2 starts closing.

10) When M2 leaf has reached the position you want to set the slowing down in closing, then press button WORK and the leaf will

start the slowing down procedure.

11) After that, M2 leaf will hit the mechanical stopper in closing and automatically will stop.

***** ATTENTION: MECHANICAL STOP necessary and mandatory !!!!! *********

(If it is not possible to install the mechanical stop and the motor, once reached the end of the run, continues pushing: after 2‐3 seconds press

and release the button WORK ; the motor stops).

12)Press button WORK to start counting the delay of the leaves in closing (Led DL6 starts flashing quickly).

13)Press again button WORK to stop the counting for the time to apply to the delay in closing. Automatically M1 leaf starts closing.

14)When M1 leaf has reached the position you want to set the slowing down in closing, then press button WORK and the leaf will start the slowing

down procedure.

15) After that, M1 leaf will hit the mechanical stopper in closing and automatically will stop.

***** ATTENTION: MECHANICAL STOP necessary and mandatory !!!!! *********

(If it is not possible to install the mechanical stop and the motor, once reached the end of the run, continues pushing: after 2‐3 seconds press

and release the button WORK ; the motor stops).

16) When the closing has finished, the control panel will automatically go out from the programming and it will be ready to work.

WARNING: In case of re‐adjustment of the trimmer RALL. or VELOC. it is ABSOLUTELY necessary to repeat the setting.