Electrolux AF Series Manuel de l'utilisateur - Page 8
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Electrolux AF Series. Electrolux AF Series 18 pages. Refrigeration
Également pour Electrolux AF Series : Manuel de l'utilisateur (18 pages)
Imprimer la page
4 initial start up/electronic display controls – electronic models electrolux refrigeration
Initial start up
The appliance transfers heat from food placed inside the
appliance to the outside air.
This process makes the rear, the sides and the area
adjacent to the doors, particularly at initial start up,
feel warm. This is normal.
There is a cooling coil located behind the rear wall of the
cabinet. This coil cools and removes moisture from the air.
A fan then circulates cold, dry air throughout the cabinet.
This air circulation means that foods are refrigerated far
more quickly than in appliances where the air remains
relatively static.
Avoid placing food against air outlets as this will
affect air circulation (see diagrams on inside cover).
A light frosting will occasionally occur on the cold interior
of the freezer when the door is opened frequently. This is
normal and will disappear after a few days in most climates.
Make sure you fully close the freezer door after you load or
remove food. If the door is left partly open, a heavy frost will
coat the inside of the freezer. If a frost develops, remove it.
Take care to properly close the door and the frost will not
reoccur.
Your new energy efficient appliance uses a high-speed
compressor and other energy efficient components that
may produce different noises to your old appliance.
These sounds are normal and include:
• compressor running noise.
• air movement noise from the small fan motor.
• occasional gurgling, similar to water boiling.
• a popping noise, heard during automatic defrosting.
• a clicking noise, just prior to the compressor starting up.
These noises are normal and not cause for alarm.
Further details can be found on page .
tips and information
•
On a top mount freezer (TM) refrigerator (where the
freezer is on top of the fresh food compartment):
Do not place food forward of the ribs on the bottom of
the freezer, it will keep the door open. So make sure
food is stored behind the ribs.
•
On a bottom mount freezer (BM) refrigerator, single door
all refrigerator (AR) and single door all freezer (AF):
Ensure freezer baskets and shelves are pushed
completely back to prevent them holding the door
open.
Electronic display controls – electronic
models only
The electronic display panel consists of an LCD display with
white backlighting and 6 push buttons. When the power
is first turned on, you will see the default settings, with the
white backlighting on.
If no buttons have been pressed and the fridge door is
closed the backlighting will turn off after 30 seconds.
tips and information
A good indication of optimal freezer temperature is ice
cream that is frozen, but still soft enough for easy scooping.
For the fridge compartment, we recommend using drinking
water and simply adjusting the fridge controls until the water
is at your ideal temperature.
Controlling the temperature
The default temperature for the refrigerator is 3°C, with a
default of -8°C for the freezer. If you want to change the
temperatures, use the instructions below. You should make
only small adjustments and wait 24 hours to see whether
you need to make further changes.
Note:
When you set a temperature, you set an average temperature
for the whole appliance cabinet. Temperatures inside each
compartment may vary, depending on how much food you
store and where you place it. High or low room temperature
may also affect the actual temperature inside the appliance.
Changing the freezer temperature
Press the freezer button to make the freezer colder in °C
steps. Once -23°C is reached the display will return to
-4°C with the next button press. You'll notice that the bar
graph gets smaller with colder freezer settings.
Ribs
Changing the refrigerator temperature
Press the fridge button to make the fridge colder in °C
steps. Once 0°C is reached the display will return to 7°C
with the next button press. The bar graph gets smaller with
colder settings.