Bosch FAP-OC 500Series Manuel de démarrage rapide et de sécurité - Page 6

Parcourez en ligne ou téléchargez le pdf Manuel de démarrage rapide et de sécurité pour {nom_de_la_catégorie} Bosch FAP-OC 500Series. Bosch FAP-OC 500Series 13 pages. Built-in wall ovens
Également pour Bosch FAP-OC 500Series : Manuel d'instructions d'installation (21 pages), Manuel d'utilisation (40 pages), Manuel d'installation (6 pages), Informations sur le produit (40 pages), Manuel d'installation (28 pages), Manuel de l'utilisateur (48 pages), Manuel de l'utilisateur (48 pages), Manuel d'installation (28 pages), Manuel d'utilisation et d'entretien (44 pages), Manuel d'installation (32 pages), Manuel d'utilisation et d'entretien / Instructions d'installation (40 pages), Manuel de référence rapide (4 pages), Manuel d'utilisation et d'entretien (27 pages), Manuel d'installation (24 pages), Manuel d'installation (32 pages), Manuel d'utilisation et d'entretien (24 pages), Manuel d'installation (28 pages), Manuel d'entretien (41 pages), Manuel d'utilisation et d'entretien (21 pages), Manuel d'installation (32 pages), Manuel d'entretien (36 pages), Manuel d'installation (32 pages)

Imprimer la page
Bosch FAP-OC 500Series Manuel de démarrage rapide et de sécurité
5 Settings

5.1 Available Settings

Below are some commonly used settings. To see all the settings refer to the full online manual or go to Dishwasher » Settings in
the Home Connect
app.
®

5.2 Adjusting the settings

First Steps to adjust any setting:
Open the door and press the ON/OFF button.
Hold down Button A for 3 seconds, until the Rinse Aid
indicator light flashes.
Release button, then follow steps below to adjust specific
setting.
To adjust the rinse aid:
1.
Press the Start button repeatedly until the right amount
of rinse aid has been set. 0 (off), 1(low), 2(medium),
or 3(high) LEDs above cycle buttons will light up
accordingly.
2.
Press button A for 3 seconds to save the setting.
To turn on intensive drying:
1.
Press button A until the Clean and Sanitize lights flash.
2.
Press the Start button until 1 LED light above the heavy
cycle button is on (intensive dry is on).
3.
Press button A for 3 seconds to save the setting.

6 Frequently Asked Questions

Q:
Why is food remaining on dishes after I run the cycle?
•
It is possible the dishes do not have adequate clearance between them. Also, be sure nothing is blocking the spray arms and
that the filter is clean. Select the Heavy cleaning cycle.
Q: Why does the cycle run a long time?
•
Sensors in the dishwasher automatically increase the cycle time to ensure a good wash when heavy soil is detected.
•
Incoming water may not be hot enough and dishwasher has to heat it.
Setting
Rinse Aid
Off/Low/Medium/High
Intensive drying
Off/On
End of cycle tone
Off/Low/Medium/High
Factory setting
Description
Medium
Setting to adjust the amount of rinse aid
used in each cycle.
Off
Setting to increase drying ability for glass-
es or plastic. Increases cycle length and
temperature.
Medium
The volume of the tone signalling the end
of cycle.
To adjust the signal volume:
1.
Press button A until the Clean and Rinse Aid lights flash.
2.
Press the Start button repeatedly until the preferred
volume level has been selected. 0 (off), 1(low), 2(medi-
um), or 3(high) LEDs above cycle buttons will light up
accordingly.
3.
Press button A for 3 seconds to save the setting.
To reset to factory settings:
1.
Press button A until the Clean, Sanitize and Rinse Aid
lights flash.
2.
Press the Start button. The 3 LEDs above cycle buttons
will blink alternatively for 1 minute. The factory settings
have been restored.
Tip: The simplest way to change the settings is with the
Home Connect
app.
®