AirStage ABYA018GTEH Manuel d'installation - Page 13

Parcourez en ligne ou téléchargez le pdf Manuel d'installation pour {nom_de_la_catégorie} AirStage ABYA018GTEH. AirStage ABYA018GTEH 15 pages.

Imprimer la page

(1) Indoor unit address

Rotary switch (IU AD × 1) ......................Factory setting "0"

Rotary switch (IU AD × 10) ....................Factory setting "0"

When connecting multiple indoor units to 1 refrigerant system, set the address at IU

AD SW as shown in the Table A.

(2) Refrigerant circuit address

Rotary switch (REF AD × 1) ..................Factory setting "0"

Rotary switch (REF AD × 10) ................Factory setting "0"

In the case of multiple refrigerant systems, set REF AD SW as shown in the Table A

for each refrigerant system.

Set to the same refrigerant circuit address as the outdoor unit.

Table A

• If working in an environ-

ment where the wireless

remote controller can be

Address

used, the addresses can

also be set using the

Refrigerant

remote controller.

circuit

• If setting the addresses

using the wireless

remote controller, set

the indoor unit address

and refrigerant circuit

address to "00".

(For information on set-

ting using the wireless

remote controller.)

⁞

* Do not set the indoor

unit address (IU AD

SW) at 64 to 99.

It may result in failure.

⁞

7.2. Custom code setting

Selecting the custom code prevents the indoor unit mix-up. (Fig. B)

(Up to 4 codes can be set.)

Perform the setting for both the indoor unit and the remote controller.

Fig. B

Confusion

Indoor unit

Remote

controller

Custom code setting for indoor unit

Set the DIP switch SET 3 SW1, SW2, referring to the Table B.

Dip switch "SET 3"

OFF

Table B

A (Factory setting)

DIP switch SET 3 SW1

DIP switch SET 3 SW2

7.3. Function setting

• FUNCTION SETTING can be performed with the wired or wireless remote controller.

(The remote controller is optional equipment)

• Refer to the wired or wireless remote controller manual for detailed setting information.

• Refer to "7.1. Setting the address" for indoor unit address and refrigerant circuit address

settings.

• Turn the power of the indoor unit ON before starting the setting.

* Turning on the power to the indoor units initializes EEV, so make sure the piping air tight

test and vacuuming have been conducted before turning on the power.

* Also check again to make sure no wiring mistakes were made before turning on the

power.

Function details

Function

Setting number

number

00 Standard

Filter indica-

01 Longer

tor interval

02 Shorter

00 Enable

01 Disable

Filter indica-

Display only on

tor action

central remote

controller

(Forbidden)

Rotary switch

Address

setting

REF AD SW

IU AD SW

Indoor unit

× 10

× 1

× 10

⁞

Code change

IU AD

REF AD

RC AD

×10

×1

×10

×1

SET3

SET4

Custom code

OFF

Default

Details

Adjust the filter cleaning interval noti-

fication. If the notification is too early,

change to setting 01. If the notifica-

tion is too late, change to setting 02.

Enable or disable the filter indicator.

Setting 02 is for use with a central

remote controller.

Function

number

Horizontal

swing airflow

direction

(Forbidden)

Cool air

temperature

trigger

Heat air

temperature

trigger

× 1

Auto restart

Cool Air

Prevention

⁞

External

control

⁞

Error report

target

Fan set-

ting when

cooling

thermostat

OFF

Switching

function for

external

inputs

(Forbidden)

Auto mode

type

Deadband

value

(Forbidden)

Setting number

Default

Adjust the horizontal swing airflow

00 Standard

direction.

01 Left half

(For horizontal swing equipped

02 Right half

models)

Adjust the cool air trigger tempera-

00 Standard

ture. To lower the trigger tem-

01 Adjust (1)

perature, use setting 01. To raise the

02 Adjust (2)

trigger temperature, use setting 02.

Adjust the heat air trigger tempera-

00 Standard

ture. To lower the trigger temperature

01 Adjust (1)

by 6 degrees C, use setting 01. To

02 Adjust (2)

lower the trigger temperature by 4

degrees C, use setting 02. To raise

03 Adjust (3)

the trigger temperature, use setting

03.

00 Enable

Enable or disable automatic system

restart after a power outage.

01 Disable

00 Super low

Restrain the cold airflow with making

Follow the

the airflow lower when starting heat-

setting on

ing operation. To correspond to the

the remote

ventilation, set to 01.

controller

Allow an external controller to start

00 Start/Stop

or stop the system, or to perform an

Emergency

emergency stop.

stop

* If an emergency stop is performed

from an external controller, all re-

frigerant systems will be disabled.

* If forced stop is set, indoor unit

02 Forced stop

stops by the input to the external

input terminals, and Start/Stop by a

remote controller is restricted.

00 All

Change the target for reporting

errors. Errors can either be reported

Display only on

in all locations, or only on the central

central remote

remote controller.

controller

When set to 01, the fan stops when

Follow the

the thermostat is OFF in cooling

setting on

operation. Connection of the wired

the remote

remote controller (2-wire type or

controller

3-wire type) and switching its therm-

01 Stop

istor are necessary.

Forced ther-

mostat off

Setting is required when connecting

a refrigerant-leak detecting device.

(Forbidden)

(only for J-IIIL series)

Refrigerant

leak detection

Single

Switch the setting method of

setpoint auto

auto mode to single or dual

mode

(cooling/heating).

(traditional)

For heat pump systems, it is

Dual setpoint

necessary to set the master indoor

unit (by wired remote controller).

auto mode

00 0°C

01 0.5°C

02 1.0°C

03 1.5°C

Choose the minimum temperature

between cooling and heating

04 2.0°C

settings (deadband) for Dual

05 2.5°C

setpoint auto mode (set in No. 68).

06 3.0°C

07 3.5°C

08 4.0°C

09 4.5°C

Details

En-12