Electrolux WRT5B1EW4 Manuel d'utilisation et d'entretien - Page 7

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation et d'entretien pour {nom_de_la_catégorie} Electrolux WRT5B1EW4. Electrolux WRT5B1EW4 18 pages. Top mount refrigerator

Imprimer la page
TOREMOVE F REEZER H ANDLE:
(HandIes may be
easier to reverse whiIe doors are offl)
1.
Remove two screws attaching handle to bottom of freezer
door.
2.
Remove short trim piece by sliding trim straight up and off
of handle bracket.
3.
Remove screw attaching top of handle to door.
4.
Magnetic
Nameplate
Mode_s: Gently pry magnetic
nameplate frame from door. Remove nameplate from its
frame, turn frame upside down and install _nold nanale
holes. Insert magnetic namepIate into frame.
Se_f-Adhesive
Nameplate
Models:
Gently peel off
nameplate from door
and reappIy over old
handle holes.
-Irim --,
TO ATTACH
FREEZER
HANDLE:
1.
Reinstall handle on
opposite side, using
same hole as
nameplate.
2.
Attach handle to
bottom of door.
3.
Slide trim piece
straight down onto
handle brackeL
Self Adhesive
NamePlate
Screw_i
(some models)
TO REMOVE FREEZER HANDLE:
(Handles may be easier to reverse while doors are off.)
1.
Remove two screws attaching handle to bottom of freezer
door.
2.
Remove button plug using edge of putty knife.
3.
Remove screw on side of freezer door and remove
handle,
TO ATTACH
FREEZER
HANDLE:
1.
Secure side of
handle
todeer and
replace button plug.
Button
2.
Secure handle to
bottom of door.
(Handles may be easier to reverse while doors are off.)
1.
Remove two screws attaching handle to bottom of freezer
door.
2.
Swing bottom of handle away from the door and slide
handle straight up and off of dovetail button.
3.
Remove screw and dovetail button and install on other
side, using the same holes as nameplate.
4.
Magnetic
Nameplate
_ode_s: Use putty knife to gently pry
magnetic nameplate frame from door. Remove nameplate
from its frame, turn frame upside down and install in old
handle holes. Insert magnetic nameplate into frame.
Self-Adhesive
Nameplate
Models:
Use putty knife to
gently peel off nameplate from door and reappiy over old
handle holes.
TO ATTACH
FREEZER
HANDLE:
Nameplate
Nameplate
1.
Start with handle
(sememodels)
J_rarne_q
offset
away
from
doon Place top of
handle over dovetail
button, swing handle
into an upright
position and pull
IScrew J
\\"_m_m,_/"
"..
downward, locking k
-H_/L_.
_
nte p ace
2.
handleSecure
withb°tt°mtwo°f
screws removed
sorew----:-;J
Dovetail Button
earlier.
TRIM REMOVAL
(FULL-LENGTHTRIM
MODELS
ONLY)
In some models, the refrigerator door has a full length trim
piece which continues from the bottom of the handle to the
bottom of the door. The top of the trim attaches to the handle
bracket (Figure 1) or fits around the base of the handle (Figure
2). An adhesive "trim lock" is positioned about halfway down.
The bottom of the trim is held in place by either an adhesive
trim lock, or a trim lock with two prongs inserted into a hole on
the face of the doon
TO REMOVETRIM:
1.
Remove trim by gently pulling trim lock areas out and
away from door.
2.
When trim is free from door, slide the trim straight down
and away from base of handle.
i_!i'i_i!
,!i_ii_ii_ii_ii_ii_ii_ii_ii_ii_iiii_iii_il
_i_i_i_ii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_ii_ii_ii_ii_ii_ii_i_i_i_i_ii_i_i_i_i_ii_ii_ii_iii_i_!_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_
_i_i_ii_i_i_i_i_i_i_i_i_i_ii_i_i_i_i_i_i_i_i_i_i_iii_i_i_i_i_i_i_i_ii_ii_ii_ii_ii_ii_iiii_!ii_i_i
_i_i_iii_ii_ii_i_i_i
_!_i_i_i_i_i_i_i_i_i_i_iii_ii_iiiiiiiiiiiiiiiiiiiiiiiii_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_ii_i_i_i_i_i_i_i_i_i_i_i_i_i