Draper FlexShade Instructions Installation et fonctionnement - Page 2
Parcourez en ligne ou téléchargez le pdf Instructions Installation et fonctionnement pour {nom_de_la_catégorie} Draper FlexShade. Draper FlexShade 12 pages. Exterior clutch-operated shade
Également pour Draper FlexShade : Manuel d'installation et d'utilisation (8 pages), Instructions d'installation (2 pages), Manuel d'instructions (12 pages), Instructions d'installation et d'utilisation (11 pages), Instructions Installation et fonctionnement (12 pages), Instructions Installation et fonctionnement (16 pages), Instructions Installation et fonctionnement (4 pages), Manuel d'instructions (7 pages), Instructions Installation et fonctionnement (16 pages)
Imprimer la page
Exterior Clutch-Operated FlexShade
PLEASE READ - Important Safety Information
Important Safety Information
Improper installation and use of the Exterior Clutch-Operated FlexShade
to imprecise installation, mishandling of the shade during installation, or installation on an insufficient wall or ceiling structure. Please use extreme care.
1. Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and could
result in serious injury.
2. Installation and calibration of the shade should only be performed by an
authorized, qualified, and experienced professional.
3. Do not affix the unit to wall or ceilings that have inadequate strength to
permanently hold the unit during use. It is the owner's and installer's
responsibility to confirm the wall or ceiling to which the unit attaches is
sufficient to permanently hold the weight and stress loads of the unit at all
times. Draper
, Inc., is not responsible for improper installation, application,
®
testing, or workmanship related to the product at place of installation.
4. It is the installer's responsibility to make sure appropriate fasteners are
used for mounting.
5. All brackets, fascia, headboxes, pockets, wall clips, and other hardware
must be installed level. Shade unit must be level and square.
6. Before testing or operation, carefully inspect the entire area and path
of the shade and areas underneath the shade to be sure no persons
or objects are in the area.
1. Look for any job site conditions that could interfere with installation or
operation of the system.
2. Read carefully and be sure to understand all installation instructions and all
related operations manuals. These instructions are intended to serve as a guide
for the installer and owner. They should be followed closely and combined with
the expertise of experienced qualified installers. Draper, Inc., is not responsible
for improper installation, application, testing, or workmanship related to the
product at place of installation. Please retain all instructions for future use.
ANSI/WCMA A100.1-2018 standard
was established on December 15, 2018, to eliminate strangulation hazards for small children from hanging cords and chain loops.
When Draper
dealers specify that custom shades comply with ANSI/WCMA A100.1-2018, Draper provides a pre-installed Spring-Loaded
®
Chain Tension Device
(shown at right)
included. When properly installed, the tension device prevents the creation of a hazardous loop by maintaining tension on the bead chain.
If not installed properly, the shade is partially inoperable. A warning label
For more information, please see the Draper ANSI/WCMA A100.1-2018 compliance page:
PLEASE READ - Field Adjustments
Each Draper Solar Control Shade is tested to
ensure proper operation. Even with this testing,
some field adjustments may be needed for
telescoping.
If the shade is telescoping, place a piece of
shimming fabric into the fabric roll when the shade
is deployed on the side that the fabric will be drawn
toward. For example: if the fabric is tracking to the
left, place the shimming fabric on the right side.
WARNING
Before Beginning Installation
Child Safety Information
(developed by the Window Coverings Manufacturer's Association and the Consumer Product Safety Commission)
for clutch-operated units. A warning label is attached to the kit and approved mechanical fasteners are
PLEASE READ - Cleaning and Maintenance
Window covering products manufactured by Draper, when properly installed, should require no operational
maintenance or lubrication.
Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush attachment.
They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy water. A mild
dishwashing liquid is recommended. A clean dry cloth is recommended for the metal finish.
Please Note: Exceptions are GreenScreen Evolve
SW7000 fabrics, which must be cleaned with a dry art sponge.
(GreenScreen Revive
registered trademark of Phifer
®
can result in serious injury or death. Primarily, injuries can occur if the unit falls due
®
7. During testing or operation, carefully watch the surrounding area for any
potential safety concerns including nearby persons or objects.
8. After installation, the entire system should be carefully tested to ensure safe
and normal operation. Extreme care should be taken during testing to remain
clear of moving parts to avoid possible injury.
9. Operation of shade should be performed only by authorized and qualified
personnel, who have been trained in the safe and effective operation of the
shade and understand its safety features.
10. The safety features of the shade should never be disabled, bypassed, or
overridden. The system should not be operated until all safety features are
properly and completely installed, calibrated, and tested.
11. Shade may need to comply with local, state, or district rules and regulations, in
particular when installed in schools. All applicable rules and regulations should
be reviewed before installation and use.
12. Failure to precisely follow installation guidelines invalidates all warranties.
13. Custom products/installations may not be reflected in this manual.
Call Draper, Inc., if you have questions regarding your installation.
3. Open cartons lengthwise, taking care not to cut into cardboard shipping
container.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper shade and parts.
6. If you have any difficulties with installing, servicing, or operating your shade,
call your dealer or Draper, Inc., 765-987-7999.
is also added to the shade roller.
(shown below)
www.draperinc.com/windowshades/wcmacompliance.aspx
and GreenScreen Evolve
are registered trademarks of Mermet
®
®
Incorporated.)
®
page 2 of 12
Important Safety Information
, GreenScreen Revive
, Flocké
, and Phifer
®
®
®
USA. SheerWeave
®
®
is a
®