Draper Paragon V Series Instructions d'installation et d'utilisation - Page 2

Parcourez en ligne ou téléchargez le pdf Instructions d'installation et d'utilisation pour {nom_de_la_catégorie} Draper Paragon V Series. Draper Paragon V Series 2 pages.

Imprimer la page

Paragon/Series E and V 220V by Draper

Optional Wall

Case Width

Mounting

> 244 and < 457 cm

Bracket

> 457 and < 610 cm

> 610 and < 878 cm

25 mm

Brackets are equally spaced from each

other and each end. For example, if the

case length is 513 cm, then each of the

two brackets will be placed approxi-

73 mm

mately 171 cm from each end (with 171

83 mm

cm between them).

73 mm

83 mm

73 mm

" (12 mm) dia.

" (9.5 mm) dia.

Bottom Closure Removal/Replacement

Removal and replacement of the bottom closure panel

requires two people positioned about 152 cm from each end

of the panel. Closure should be handled as shown in Step 5

below to prevent bowing of the closure during handling.

Before removing

bottom closure, you

must first remove

screws at each end

of case (see drawing

at right).

Screw and washer

Caution: Be sure to replace screws

and washers at each end of case

when replacing closure!

Step 1

Step 2

Step 3

Step 4

Case Dimensions*

No. of

Intermediate

Brackets

<244 cm

Tab-Tension

Adjustment Procedure

for Paragon

Draper's Tab-Tensioning System

is factory-set; under normal

circumstances field adjustment is

not required. If you notice wrinkles,

waves or other indications that

tensioning cables need adjusting,

follow these steps:

1 Determine which side requires

adjustment.

2 Secure dowel with one hand.

Caution: Don't touch or bend

viewing surface.

3 Use Phillips-head screwdriver to

depress spring-loaded

adjustment screw. Slowly turn

clockwise to tighten tension or

counterclockwise to loosen

tension. The screw adjusts in ¼

turn increments. Adjust only one

increment (¼ turn) at a time.

4 If problem is not corrected, leave

screen in position for 24 hours to

allow surface material to stretch

into position.

5 If problem still is not corrected,

repeat steps 2 and 3.

Tensioning

Cable

Dowel

Adjustment

Screw

Step 5

See separate Se-

rial Communication-

RS232 Instruction

sheet for enabling

RS232 with the MC1.

www.draperinc.com

203

51 mm

305 mm

35 mm

337

127

51 mm

*Please Note: Optional wall brackets add 4.5 cm per bracket to case

length. Wall mounting bracket hole location is 2.54 cm from end of case.

Please Note: Do not wire motors in parallel.

Single Station Control

CE Approved

Junction box at

left end of screen

Internal Screen Wiring

Blue-220v (Common)

Brown-220v (Down)

Black-220v (Up)

Control

switch

Dashed wiring

by installer

Low Voltage and Remote Control

Program LED

Fuse

MC1

(765) 987-7999

* - Case support brackets will be evenly spaced along the case

Series E

Viewing

Surface

Wiring Diagrams

Junction box at

left end of screen

Green/Yellow (Motor Ground)

220v,

50 Hz.

220v, 50 Hz.

White or Blue-Common to screen & 110/220V AC Neutral

Red-to screen (directional)

Brown-to screen (directional)

Yellow-to 110/220V AC-Hot

Black-to 110/220V AC-Hot

Green/Yellow (Ground)

Dashed wiring by electrician

Low voltage wiring by others

Eye Port for IR Eye, RF Receiver or LED

Wall Switch. For more than one of

these, a splitter is required.

3 Button Wall Switch

DOWN - Black

COM - White

UP - Red

Aux Port for connecting additional LVC-III

modules (up to six total can be linked-

connect from Aux to Eye).

MC1

White or Blue-Common

Red-to Screen (directional)

Black-to Screen (directional)

Brown-Hot to AC

Green/Yellow-Ground

Low Voltage Wiring by others

AC Wiring by electrician

RS232 Data FROM Control System

RS232 Data TO Control System

Signal Ground & Manual Switch Common

Manual Switch Down

Manual Switch Up

Eye Port for IR Eye. For RF Receiver or LED

Wall Switch, a Splitter and a Power Supply

is required. Plug RF Receiver or LED Wall

Switch and Power Supply into splitter, then

run cable from Splitter to MC1 Eye Port.

Page 2 of 2

Varies

Series V

Viewing

Surface

Multiple Station Control

Not CE Approved

Internal Screen Wiring

Blue-220v (Common)

Brown-220v (Down)

Black-220v (Up)

Green/Yellow (Motor Ground)

Cap off with wire

nut & tape

Red

Blue

Black

Red

Blue

Black

Blue

Red

Black

Dashed wiring

by installer

Internal Screen Wiring

White/Blue (Common)

Red 110/Black 220 (Up)

Black 110/Brown 220 (Down)

Green/Yellow

(Motor Ground)

110/220V

Line

STOP

Location of key

operated on-off

switch if furnished

STOP

Control

Switches

24v DC

Internal Screen Wiring

White/Blue (Common)

Red 110/Black 220 (Up)

Black 110/Brown 220 (Down)

Green 110V/

Green/Yellow 220V

(Motor Ground)

Location of key

operated on-off

switch if furnished

To AC Line