Draper SLX17 Manuel d'installation et d'utilisation - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'installation et d'utilisation pour {nom_de_la_catégorie} Draper SLX17. Draper SLX17 7 pages. 230v ac scissor lift slx video projector lift
Également pour Draper SLX17 : Brochure & Specs (16 pages), Manuel d'installation et d'utilisation (7 pages), Instructions d'installation et d'utilisation (8 pages), Manuel d'installation et d'utilisation (7 pages)
Imprimer la page
Scissor Lift SLX by Draper
Connecting Controls
Controls plug into the data cable inputs on the Control Panel,
which is located on the Top Frame on the front side of the lift,
using RJ14 connectors.
For IR or RF Remote Control, use data cable with RJ14
connectors on both ends.
For serial control of "Show" position, use data cable with RJ14
connectors on both ends and an R2D7 Serial Control Interface.
Plug into the "RP/RQ" input.
Please Note:
Data cable connections must be made using electrically
straight 4-conductor modular cable (RJ14). If making your
own cables, this means colors do not cross over: blue
leads to blue, green to green, etc. (see diagram below).
Pin
1 2 3 4 5 6
1 2 3 4 5 6
Y G R B
Y G R B
Adjustments
CAUTION: Be sure all switches are in "Off" position before adjusting limit
switch. Always be prepared to shut lift off manually when new adjustment is
being tested. Please refer to wiring diagram.
Caution: The maintenance/service factory limit setting must not be
adjusted to a lower position than the preset factory limit setting. In addition,
Draper does not recommend setting show position at the maintenance/service
position.
Limit switches for the Scissor Lift SLX are preset at the factory. The "Up"
limit switch is set for fully closed. The "Down" limit switch is set for the fully
down (maintenance) position for the size lift you have ordered. The limit switch
assembly is located inside the lift and behind the Lifting Cable Drum.
Set Show Position
(can only be set if it is cleared, i.e. it cannot be re-set)
1 Use the three-button wall switch to lower or raise the lift to the desired
"Show Position".
2 Turn the Key Switch to the "Down" position and hold it for approximately 5
seconds. Once the lift begins to move, release the switch. The lift will
calibrate its position and stop at the final "Show Position".
Please Note: If the Scissor Lift loses or is disconnected
from the power, the "Down" function will not work until
you operate the lift in the "Up" direction. This allows the
lift's control encoder to recognize it's "home" location.
Pin
www.draperinc.com
SP-KSM
Red - Down
Green
Black - Com
Black
Black - Com
Blue - Up
Yellow
1 Using the Key Switch, lower the lift to the maximum "Down" (Service)
position then release the Key Switch.
2 Turn the Key Switch to the "Down" position and hold it for approximately 5
seconds. Once the lift begins to rise and then stops, the "Show Position"
has been cleared.
Please Note: At this point the Key Switch will not operate until the new
"Show Position" has been set. (See the operation above where "Show
Position" is not yet set.)
Remember that clearing and setting the "Show Position" does not affect
the closed position limits.
"Main" refers to commands sent via the wall switch or main channel
commands sent via IR or RF remote through the RP Bus.
The Up and Down limit switches shown in the drawing are for setting the "Up
and "Fully Down." These can be adjusted manually by loosening or tightening
the screws to increase or reduce the travel.
(765) 987-7999
Function Indicator
Low Voltage Trigger
Pin
1 2 3 4 5 6
(6-24 VDC)
Y G R B
(Polarity Independent)
RP/RQ Bus Ports for
Pin
remote controls such as
1 2 3 4 5 6
IR Eye, RF Receiver, LED
Y G R B
Wall Switch and RS232
LVC-S
DCU
Green
Black
Yellow
Pin
6 5 4 3 2 1
B R G Y
To RS232 Port:
Yellow = Rx (Data from control system)
Green = Tx (Data to control system)
Red = Unused
Black = Gnd (Signal Ground)
Clear Show Position
Down
Up
Up
Limit
Switch
Down
Limit
Switch
page 4 of 7
Pin
1 2 3 4 5 6
Y G R B