Draper FlexShade 2 Pocket Headbox Manuel d'instructions - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'instructions pour {nom_de_la_catégorie} Draper FlexShade 2 Pocket Headbox. Draper FlexShade 2 Pocket Headbox 8 pages. Maximized coverage for large, tall areas, while also reducing light gap

Imprimer la page

FlexShade

PLEASE READ - Important Installation Information

Caution:

1. Inspect all boxes to ensure you have

received the proper shades and parts.

Controls may be shipped separately, or in

same carton as shades.

2. Open cartons lengthwise, taking care not

to cut into cardboard shipping container.

PLEASE READ - Safety Information

Important Safety Information

Improper installation and use of the FlexShade

due to imprecise installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure.

Please use extreme care.

1. Please read the following installation guidelines thoroughly and follow them

carefully. Failure to do so may cause product to fall or otherwise fail, and

could result in serious injury.

2. Installation and calibration of the unit should only be performed by an

authorized, qualified, and experienced professional. In particular, electrical

work and wiring [indicated in diagram by dashed lines] must be completed

only by a qualified professional electrician who has read this manual

completely and is familiar with the construction and operation of this

equipment and the hazards involved.

3. Do not affix the unit to wall or ceilings that have inadequate strength to

permanently hold the unit during use. It is the owner's and installer's

responsibility to confirm the wall or ceiling to which the unit attaches is

sufficient to permanently hold the weight and stress loads of the unit at all

times. Draper

, Inc., is not responsible for improper installation, application,

testing, or workmanship related to the product at place of installation.

4. It is the installer's responsibility to ensure appropriate fasteners are used for

mounting.

5. All brackets, fascia, headboxes, pockets, wall clips, and other hardware

must be installed level. Unit must be level and square.

6. Never leave the area while operating the unit during installation,

maintenance, or normal operation, unless it is secure and safe.

7. Before testing or operation, carefully inspect the entire area and path of the

shade and areas underneath the shade to be sure no persons or objects are

in the area.

8. Turn off power and any nearby equipment or cables carrying electricity

before connecting switches, wires, controls, or electrical components.

9. Ensure the limit switches are pointed down or accessible when placing the

motor in brackets/endcaps.

10. All motors should be tested and limits set using test cord before shades

are wired.

11. Do not wire motors in parallel without written permission from Draper, Inc.

12. During testing or operation, carefully watch the surrounding area for any

potential safety concerns including nearby persons or objects.

PLEASE READ - Field Adjustments

Each Draper Solar Control Shade is tested to ensure

proper operation. Even with this testing, some field

adjustments may be needed for telescoping.

If the shade is telescoping, place a piece of shimming

fabric into the fabric roll when the shade is deployed

on the side that the fabric will be drawn toward. For

example: if the fabric is tracking to the left, place the

shimming fabric on the right side.

2 Pocket Headbox

3. Before mounting shades, verify

measurements on label provided with shade,

and ensure unit is installed at correct width.

4. All endcaps, fascia, headbox, and other

hardware must be installed level. Shades

must be level and square.

2 can result in serious injury or death. Primarily, injuries can occur if the unit falls

PLEASE READ - Cleaning and Maintenance

Window covering products manufactured by Draper, when properly installed, should require no

operational maintenance or lubrication.

Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush

attachment. They also may be cleaned by using a sponge or soft cloth and mild solution of warm soapy

water. A mild dishwashing liquid is recommended. A clean dry cloth is recommended for the metal finish.

Please Note: Exceptions are GreenScreen Evolve

fabrics, which must be cleaned with a dry art sponge.

(GreenScreen Revive

registered trademark of Phifer

WARNING

13. After installation, the entire system, including all sensors, should be carefully

tested to ensure safe and normal operation. Extreme care should be taken

during testing to remain clear of moving parts to avoid possible injury.

14. Operation of unit should be performed only by authorized and qualified

personnel, who have been trained in the safe and effective operation of the

unit and understand its safety features.

15. The safety features of the unit, including sensors, should never be disabled,

bypassed, or overridden. The system should not be operated until all safety

features, including the sensors, are properly and completely installed,

calibrated, and tested.

16. Unit may need to comply with local, state, or district rules and regulations,

in particular when installed in schools. All applicable rules and regulations

should be reviewed before installation and use.

17. Failure to precisely follow installation guidelines invalidates all warranties.

18. Custom products/installations may not be reflected in this manual. Call

Draper, Inc., if you have questions about the installation of custom products

or any questions about your installation.

Before Beginning Installation

1. Look for any job site conditions that could interfere with installation or

operation of the system.

2. Read carefully and be sure to understand all installation instructions and

all related operations manuals. These instructions are intended to serve

as a guide for the installer and owner. They should be followed closely and

combined with the expertise of experienced qualified installers. Draper,

Inc., is not responsible for improper installation, application, testing, or

workmanship related to the product at place of installation. Please retain all

instructions for future use.

3. Open cartons lengthwise.

4. Locate and lay out all pieces.

5. Inspect all boxes to ensure you have received the proper shade and parts.

Controls may be shipped separately, or in same carton as shade.

6. If you have any difficulties with installing, servicing, or operating your shade,

call your dealer or Draper, Inc., 765-987-7999.

and GreenScreen Evolve

Incorporated.)

6. Read the following installation guidelines

thoroughly and follow them carefully.

Failure to do so may cause product to fall or

otherwise fail, and invalidates warranty.

7. Installer is responsible for selecting mounting

hardware appropriate for site conditions.

Important Safety Information

, GreenScreen Revive

, and Phifer

are registered trademarks of Mermet

page 2 of 8

SW7000

USA. SheerWeave

is a