Bosch WIS24140GB Instructions for Use, Programme Table Manuel d'instruction - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Bosch WIS24140GB Instructions for Use, Programme Table. Bosch WIS24140GB Instructions for Use, Programme Table 8 pages. Bosch washing machine operating instructions
Également pour Bosch WIS24140GB Instructions for Use, Programme Table : Instructions d'installation et d'assemblage (10 pages), Manuel d'utilisation (8 pages), Manuel d'utilisation (8 pages), Manuel d'instruction (8 pages)

Imprimer la page
Bosch WIS24140GB Instructions for Use, Programme Table Manuel d'instruction
Safety instructions
– Read and follow the operating and installation instructions and all other information
enclosed with the washing machine.
– Retain documents for subsequent use.
Risk of electric shock
– Never pull out the mains plug by tugging the power cord!
– Insert/pull out the mains plug with dry hands only.
Danger to life
On redundant appliances:
– Pull out the mains plug!
– Sever the power cord and discard together with the plug.
Care
– Destroy the lock on the washing-machine door. This will prevent
children from locking themselves in and suffocating.
Risk of suffocation
– Keep packaging, plastic film and packaging parts out of the reach
of children.
Risk of poisioning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Caused by detergents containing solvents, e.g. stain remover/
items of washing pretreated with solvent naphtha may result in an
explosion after being loaded into the washing machine.
Before hand thoroughly rinse items of washing by hand.
1. Pull out, depress insert, take out drawer all the way.
Risk of injury
– Washing machine door may become very hot.
2. Take out insert: using your finger, press insert upwards.
3. Clean detergent dispenser and insert with water and a brush and dry.
– Caution when draining hot detergent solution.
4. Attach insert and lock into position (push cylinder onto guide pin).
– Do not climb on the washing machine.
5. Slide in the detergent dispenser.
– Do not lean on the open washing machine door.
– Do not reach into the drum in case it is still rotating.
Consumption values
Programme
Programme
Additonal function
Load
Current***
Water***
duration***
Cottons 30 °C*
+
7 kg
0.55 kWh
75 l
2:12 h
Eco
Cottons 40 °C*
+
7 kg
0.85 kWh
75 l
2:12 h
Eco
Cottons 60 °C*
+
7 kg
1.50 kWh
75 l
2:12 h
Eco
Cottons 90 °C
+
7 kg
2.51 kWh
90 l
2:12 h
Eco
Information about the indicator lights
Easy-Care 40 °C*
+
3.5 kg
0.55 kWh
55 l
1:12 h
Eco
A signal sounds and the indicator lamps for spin speed and status displays flash:
Delicates/Silk 30 °C
–
2.0 kg
0.20 kWh
39 l
0:40 h
¤
Wool 30 °C
–
2.0 kg
0.20 kWh
40 l
0:36 h
¤
¤
* Programme setting for test according to currently valid European standard 60456.
¤
¤
Information about comparability tests:
¤
¤
To test the test programmes, wash indicated load, with
Eco Plus additional function
and at maximum selectable spin speed.
¤
¤
Annual energy
Annual water
Programme
Additonal function
Load
¤
consumption
consumption
¤
¤
Cottons Eco 40 °C/60 °C
Eco
+
**
7/3.5 kg
218 kWh
10560 l
¤
¤
¤
¤
Programme setting for testing and energy labelling according to directive 2010/30/EU with cold
**
¤
¤
water (15 °C).
***
The values deviate from the indicated values depending on water pressure, water hardness,
Other displays: Switch off appliance, wait 5 seconds and switch on again.
water inlet temperature, room temperature, type and amount of washing and degree of soiling,
If the display is indicated again, call customer service.
utilised detergent, fluctuations in the mains voltage and selected additional functions.
7
8
Insert for liquid detergent
Maintenance
depending on model
Position insert for dosing liquid detergent:
Detergent-solution pump
– Completely remove detergent drawer.
Page 10
Set programme selector to Off, pull out the mains plug.
– Push insert forwards.
1. Take the drainage hose out of the holder.
Do not use insert (push upwards):
Remove sealing cap, allow detergent solution to flow out.
– For gel-like detergents and washing powders,
Put the closing cap back on the hose.
– For programmes with
Prewash.
2. Carefully unscrew the pump cover (residual water).
– Risk of electric shock! Pull out the mains plug!
– Risk of explosion! No solvents!
3. Clean the interior, pump cover thread and pump housing
(fan impeller in the detergent-solution pump must rotate).
Machine housing, control panel
– Remove detergent residue immediately.
4. Reinsert and screw on pump cover.
– Wipe with a soft, damp cloth.
Handle is upright. Insert the drain hose into the holder.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residue.
To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser II and start the
Drainage hose on the siphon
Set programme selector to Off, pull out the mains plug.
1. Loosen hose clip, carefully remove drainage hose (residual water).
Leave detergent drawer open so that residual water can evaporate.
2. Clean drainage hose and siphon spigot.
3. Re-attach drainage hose and secure connection point with hose clip.
Drum
Filter in the water inlet hose
Leave washing machine door open so that the drum can dry out.
Risk of electric shock!
Use chlorine-free cleaning agent, not steel wool.
Do not immerse Aqua-Stop safety device in water (contains electric valve).
Descaling
No washing in the machine!
Release water pressure in the supply hose:
Not required if detergent dosed correctly. However, if this does occur, follow the instructions
1. Turn off the tap!
of the descaling agent manufacturer. Suitable descalers can be purchased on our website
2. Select any programme (except
or from customer service.
3. Select
Start/Pause. Leave programme for approx. 40 seconds.
4. Turn the programme selector to Off. Pull out the mains plug!
depending on model
Clean the filter:
5. Disconnect the hose from the water tap.
Close the washing
¤
Turn on tap fully, supply
¤
Drain pump blocked;
Clean filter with small brush.
machine door
hose kinked/jammed;
clean drain pump.
¤
¤
¤
¤
properly;
clean filter
Page 10,
Page 10
and/or for standard and Aqua-Secure models:
¤
¤
¤
¤
washing may
water pressure too low.
Drainage hose/outlet
Remove hose from the rear of the appliance.
¤
¤
¤
¤
be caught.
pipe blocked; clean
Take out filter with pliers and clean.
¤
¤
¤
¤
drainage hose on the
siphon.
Page 10
6. Connect the hose and check for leaks.
Water in the base
¤
or
¤
or
¤
Motor fault. Call
pan, appliance
customer service!
¤
¤
¤
¤
¤
¤
leaking. Call
¤
¤
¤
¤
¤
¤
customer service!
¤
¤
¤
¤
¤
¤
¤
¤
¤
¤
¤
¤
Installation Instructions
9
– Risk of scalding!
What to do if ...
Allow detergent solution to cool down!
– Turn off the tap!
Water is running out.
– Correctly attach/replace drainage hose.
– Tighten screw-fitting on the supply hose.
Water not flowing in.
–
Start/Pause not selected?
Detergent not washed in.
– Tap not open?
– Filter blocked? Clean the filter.
– Supply hose kinked or jammed?
Washing-machine door
– Safety function active. Stop programme?
cannot be opened.
– Rinse Hold (without final spin) selected?
– Can be opened via emergency release only?
Programme does not start. –
Start/Pause not selected?
– Door closed?
Detergent solution is not
– Rinse Hold (without final spin) selected?
drained.
– Clean the drain pump.
– Clean outlet pipe and/or drainage hose.
Water not visible in the
– Not a fault – water below the visible area.
drum.
Spin result not satisfactory,
– Not a fault – unbalanced load detection system has stopped the spin
washing wet/too damp:
cycle, washing unevenly distributed.
Distribute small and large items of washing in the drum.
–
Reduced Ironing is selected?
– Too low speed selected?
The programme duration
– Not a fault – the programme sequence is optimised for the particular
Drain programme.
changes during the wash
wash process. This may result in changes to the programme duration
cycle.
in the display field.
Spin cycle actuated several
– Not a fault – unbalanced load detection system adjusts imbalance.
times.
Residual water in the
– Not a fault – effect of the care product not impaired.
dispenser for care
– If required, clean insert.
product
.
Odour formation in the
– Run
Cottons 90 °C programme without washing.
washing machine.
Use standard detergent.
Foam is coming out of the
– Too much detergent used?
detergent drawer.
Mix 1 tablespoon of fabric softener with ½ litre of water and pour into
dispenser II (not for outdoor, sports and down-filled textiles!).
– Reduce detergent dosage for the next wash cycle.
Loud noise formation,
– Appliance feet fixed?
vibrations and "Wandering"
Secure appliance feet.
Spin/
Drain).
during spin cycle.
– Transportation protection devices removed?
Remove transportation protection devices.
Noises during spin
– Clean the drain pump.
and drain cycles.
Indicator lights do not
– Power failure?
function while the
– Fuse tripped? Switch on/replace fuse.
appliance is running.
– If the fault occurs repeatedly, call customer service.
The programme takes
– Not a fault – unbalanced load detection system adjusts imbalance
longer than usual.
by repeatedly distributing the washing.
– Not a fault – foam detection system active – a rinse cycle is
switched on.
Detergent residue on the
– Occasionally phosphate-free detergents contain water-insoluble
washing.
residue.
– Select
Rinse/Freshen Up or brush the laundry after washing.
In the pause status
– Water level too high. Washing cannot be reloaded.
Start/Pause flashes very
Immediately close washing machine door.
quickly and a signal
– Select
Start/Pause to continue the programme.
sounds.
If a fault cannot be rectified (switching the machine on and off) or a repair is required:
– Set programme selector to Off and pull out the mains plug.
– Turn off the tap and call customer service.
Installation Instructions
10
Page 10
Page 4
Page 3, 4
Page 6
Page 3, 4
Page 10
Page 5
Page 5
Page 9
Installation Instructions
Installation Instructions
Page 10
Washing machine
en Instruction manual
11