Bosch HBC38D754 Manuel d'instruction - Page 7
Parcourez en ligne ou téléchargez le pdf Manuel d'instruction pour {nom_de_la_catégorie} Bosch HBC38D754. Bosch HBC38D754 36 pages. Combination steam oven
Imprimer la page
Moisture sensor
The moisture sensor is located at the top on the right of the
cooking compartment ceiling. When types of heating involving
steam are used, it measures the moisture content in the
cooking compartment.
You save energy and water because only so much steam as is
required is produced.
Steam condenses on the moisture sensor and drips down. This
is normal.
Before using the appliance for the first time
In this section you will find out which steps are required before
using the appliance for the first time:
Setting the clock and language
■
Setting the water hardness range
■
Starting the appliance for the first time
■
Cleaning the accessories before use
■
Fitting the grease filter
■
Setting the clock and language
After making the electrical connection, "Set the clock" appears
in the display. Set the clock and the language for the display, if
required.
8KU]HLW HLQVWHOOHQ
2EHU8QWHUKLW]H
8KU]HLW
&
PLW VFKOLHHQ
Set the current time using the rotary selector.
1.
Press the
button to switch to "Select language".
X
2.
Set the required language using the rotary selector.
3.
30 different languages are available.
Press the
0
button.
4.
The time and language are applied. The current time is
displayed.
Setting the water hardness range
Descale your appliance regularly. This is the only way to
prevent damage.
Your appliance automatically displays when it needs descaling.
It has been preset to water hardness range "medium". Change
the value if your water is softer or harder.
You can check the water hardness with the test strips supplied
or ask your water supplier.
If your water is very hard, we recommend that you use softened
water.
You can only dispense with descaling completely if you
exclusively use softened water. If this is the case, change the
water hardness to "softened".
Caution!
When cleaning the moisture sensor, do not bend or push in the
sides. That may cause malfunctions.
You can change the water hardness range in the basic settings
when the appliance is switched off.
If required, press the
%
1.
Press and hold the
°
button until "Select language" appears
2.
in the display.
Press the
button until "Water hardness" appears.
X
3.
"2-medium" is highlighted in the display.
Change the water hardness using the rotary selector.
4.
Possible values:
softened
1-soft
2-medium
3-hard
4very hard
Press the
button to exit basic settings.
°
5.
The change is saved.
Before first use
Before first use, heat the empty appliance for 20 minutes at
100 °C with the Steam type of heating. Do not open the
appliance door during this time. The appliance is automatically
calibrated (see section: Automatic calibration).
Press the
button to switch on the appliance.
%
1.
The "Hot air" type of heating appears after approx.
4 seconds.
Fill the water tank and insert it (see section: Filling the
2.
water tank).
Before using for the first time, moisten the tank cover seal
with a little water.
Turn the rotary selector until "Steam" appears.
3.
Press the
n
button.
4.
The appliance heats up to 100 °C. The cooking time
(20 minutes) does not start to count down until the set
temperature has been reached. Do not open the appliance
door during this time.
The cooking operation automatically ends and a signal
sounds.
Press the
button to switch off the appliance.
%
5.
Leave the appliance door ajar until the appliance has cooled
down.
Cleaning the accessories before use
Using soapy water and a soft cloth, clean the accessories
thoroughly before first use.
button to switch off the appliance.
-
I
II
III
IV
7