Anchor Xtreme XTR-6000CU2 Manuel du propriétaire - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} Anchor Xtreme XTR-6000CU2. Anchor Xtreme XTR-6000CU2 4 pages. Portable sound system

Imprimer la page

DIVERSITY WIRELESS BY ANCHOR AUDIO

Anchor Audio UHF wireless is a 16 channel, diversity wireless system that receives signals with two independent antennae.

With diversity wireless the receiver processes the stronger signal, effectively minimizing dropouts and interference from other

transmitting sources. The antennae are mounted internally so there are no obstructions or risk of damage.

CHANNEL SELECTION - BUILT-IN RECEIVER

Select a channel, set the built-in receiver & microphone transmitter to that channel before useing your wireless system.

1. Choose any available wireless channel/frequency from 1 thru 16 (see page 7 for transmitter setup instructions)

2. Turn the Wireless Channel Selector Knob to the channel/frequency you choose in step 1

If you have two wireless receivers repeat above for the second receiver. Remember each receiver/transmitter pair must be set

to different channels for proper operation.

NOTE: Ongoing wireless interference? The frequency you selected may be in use by

other systems in the area! Change channels until you find a clear frequency!

WIRELESS VOLUME

WIRELESS CHANNEL

CONTROL

SELECTION KNOB

RX INDICATOR LIGHTS

OPERATING THE BUILT-IN CD PLAYER

Your built-in CD player features 'direct-in' play, power loading, anti-shock/skip CD mechanism, repeat & random play, three beam

laser tracking system and dual one bit D/A converters. By feeding the CD audio signal directly into the mixing bus the Xtreme Sound

System is able to create a crisp, clear composite output of all your system inputs.

CD PLAYER BASIC OPERATION

Insert a disc into the player by gently sliding it, label side up, into the CD slot. The player will automatically load and begin playback

from the beginning of the disc. CD player controls are explained in detail below:

PLAY/PAUSE Press to play a loaded CD. Press during play-

back to pause, press again to resume.

Press once to advance CD to next track. Press

and hold to fast forward on the current track.

DOWN

Press once to go to previous track. Press and

hold to fast backward on current track.

EJECT

Press to unload a disc from the player. If CD

is not removed within 10 seconds it will be

automatically reloaded into the player.

CAUTION: To avoid noise at shut off, turn CD player off before you turn off the Xtreme!

CD SLOT

CD PLAYER LCD DISPLAY

CD POWER ON/OFF

TOP TRACK Press once to start playing the disc from the

first track.

RANDOM

Press for continuous, random track play-back.

Press again to resume normal play.

REPEAT

Press for continuous playback of the same

track. Press again to resume normal play.

POWER

Press to turn the CD player on/off. The sound

system will need to be turned off separately.

FEEDBACK

Feedback, a howling noise or shrill sound, is self-generated by the sound system. It's caused by a microphone picking up the sound

coming from the speaker and then re-amplifying it. Once a feedback loop starts it continues until the system is adjusted.

FEEDBACK CAUSES

• Microphone too close, pointing towards

or in front of speaker

• Volume setting is too loud for room

• Sound reflecting off hard surfaces

AVOIDING & ELIMINATING FEEDBACK

• Point microphone in a different direction

• Keep microphone away from the speaker

• Place speaker in FRONT of the microphone

• Reduce the sound system volume levels

CONNECTING TWO OR MORE XTREME SOUND SYSTEMS

USING A XTREME UNPOWERED COMPANION SPEAKER (XTR-6001)

Connect one end of a speaker cable (SC-50NL) to the COMPANION SPEAKER OUTPUT jack on the back of a powered Xtreme

sound system. Connect the other end to the jack labeled IN on the back of a Xtreme unpowered companion speaker.

NOTE: AC power is not required for an unpowered companion speaker.

USING POWERED XTREME SYSTEMS

The Balanced Line Output feature allows you to connect two or

more powered Xtreme's and control all volume levels from the

primary system.

1. Connect a speaker cable (EX-50PP) to the BALANCED

LINE OUT jack on the first/primary powered Xtreme

2. Connect other end of cable to the BALANCED INPUT

jack on the second powered Xtreme

3. Set the Level Control for the Balanced Input on the

second Xtreme to maximum

4. Connect additional systems following 1 - 3 above

NOTE: The Balanced Line Output feature can also be used to send the signal to a

sound system in a different room or a separate recording device.

SPEAKER STAND SETUP

1. Loosen the Lower Collar Knob

LOWER

2. Separate the stand legs until

COLLAR

KNOB

the leg support Cross Braces

are parallel to the floor

3. Tighten the Lower Collar Knob

CROSS BRACES

CORRECT SYSTEM PLACEMENT

WRONG SYSTEM PLACEMENT

CAUTION: Feedback can damage your equipment

& may be hazardous to hearing.

EX-50PP CABLE

FIRST POWERED

XTREME SYSTEM

SECOND POWERED

UPPER

COLLAR

4. Loosen the Upper Collar Knob and

KNOB

extend the center pole

5. Adjust height and retighten the

Upper Collar Knob

6. Place your Anchor sound system

on the stand

XTREME SYSTEM