Electrolux EIDW6105GB1A Instructions d'installation

Parcourez en ligne ou téléchargez le pdf Instructions d'installation pour {nom_de_la_catégorie} Electrolux EIDW6105GB1A. Electrolux EIDW6105GB1A 2 pages.

Imprimer la page

Dishwasher

Installation

Instructions

Printed in U.S.A.

154671001

02/08

INSTALLER: Leave Installation Instructionswith

owner.

OWNER: Read your dishwasher

Use and Care Manual.

It contains

important safety information for operating this appliance. It also has

many suggestions for getting the best results from your dishwasher.

Read all instructions

before

installing

dishwasher.

For your safety, please read and observe all safety

instructions. This guide will help you anticipate drain, water, and

electrical connections, and help you select the best location for the

dishwasher.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Failure to follow this warning can result in serious

injury.

Cut Hazard

To prevent serious injury from sharp edges, wear work

gloves when handling, unpacking or disassembling

unit.

Tools and Materials Needed for

Installation (Not I ncluded)

Drill, Electric

Driver, Socket 5/s2", 1 /4",5/16"

Flaring Tool / Tube Cutter (for copper tubing)

Flashlight

Level

Pipe Joint Compound (for iron pipe plumbing) or

Pipe Thread Tape (for sealing threads)

•

Pliers

•

Safety Glasses

•

Saw, Keyhole or V2", 11/2"to 2" Hole Cutters

•

Screw Drivers, Slotted and #2 Phillips (magnetic tip

preferred)

•

Tape, Electrical or Duct

•

Tape, Measuring

•

Wire Stripper or Utility Knife

•

Wrench, Hex-end

•

Wrenches, 2 Adjustable

(for copper tubing)

or2 Pipe wrenches

(foriron pipe plumbing)

Parts You Will Need*

(Not Included)

• Drain Hose Clamp, 1'h" Diameter

• Brass Elbow, 90 ° with a s/s"National Pipe Thread

• Conduit Connector (UL Listed)

• Wire Nuts, three (3) for 12-14 gauge wire (UL Listed)

If required:

• "Y" Branch Tailpieceand

Connector Kit (See Step 4)

• Air Gap Kit (See Step 4)

All the parts can be found at local hardware, electrical and

plumbing supply stores.

Electric Shock Hazard

Disconnect electrical

power at the fuse box or

circuit breaker box before beginning installation.

Failure to follow this warning could result in death

or serious injury.

NOTE: Put unit on its back being careful not to pinch the Water

Drain Hose.

Remove two (2) screws at front of the kickplate assembly using a

#2 Phillips screw driver.

Tilt and pull forward to remove see figure 1.

NOTE: It is not necessary to remove the outer door for installation.

lilckplate Assembly

Outer

Door

Top Screws

Kickl:

Toeplate

Figure

Locate water inlet valve behind kickplate on bottom left underside

of unit.See Figure 4. The valve has a 3/8"NPT female fitting.

Remove Plug

Wrap 90 ° elbow (not included) with pipe thread tape (or apply

joint compound) and thread it into water inlet valve. When

tightened, elbow should point toward the left. To prevent bending

of bracket or breaking of valve, avoid overtightening.

See Figure 4.

Cabinet Preparation:

As a precaution, it is recommended,

but not required that the

cabinets enclosing all sides of the dishwasher (including the

underside of the countertop) be sealed with an oil based paint

or moisture-proof polyurethane to prevent possible steam/

moisture damage.

Electric Shock Hazard

Observe all local codes and ordinances for

electrical and plumbing connections. All electrical

and plumbing work should be performed by

qualified persons. Failure to follow this warning

could result in death or serious injury.

Make sure your location has the correct drain, water, and

electrical outlets to make the connections. Do not install unit

under a cooktop range. Damage to tub or other components will

occur.

34"

rain.

35"

maxf*

13/4"

3 I/2"min.to

41/2" m ax.

- 1a/4"

Front

Electrical, water,

and drain lines

must be confined

to shaded area.

Preferred

Drain Areas

**NOTE:

35" max. height for

standard cabinetry cutout.

(s/,_, m in. clearance

required from unit to

underside of countertop.)

Left

497/_ ''

Doorin900

open position

Right

",_

22//'--

Power supply/water

inletlocation

*DIMENSIONS

DO NOT

IN CLUED E INSULATION

IMPORTANT:

For proper operation and appearance of unit,

cabinet opening should have dimensions as shown in Figure 2.

If unit is to be placed in a corner, there must be at least a 2-inch

side clearance to open door.

Floor should be flat and free of any obstruction.

IMPORTANT:

Drain, water, and electrical

lines should be

roughed-in before going any further.

Electric Shock Hazard

Electrical, water, and drain lines must be confined

to shaded areas in Figure 2.

Electric conductors, water, and drain could be

damaged.

Failure to follow these instructions

could result in

fire or electric shock.

NOTE: If dishwasher

is installed at end of a cabinet, sides and

back must be fully enclosed.

NOTE: Cabinet Seal Kit (Kit # 154662101).

This kit provides a

seal between the unit and cabinets once installation is

complete. (The Installation

Instructions are located in the Kit)

Locating the Connections

Review dimensions in Figure 2 to locate dishwasher's drain,

water, and electrical connections.

All utilities must be routed in shaded area in the Figure 2.

IMPORTANT:

Disconnect power before starting installation.

Note: Locate the electrical supply and dishwasher's electrical

junction box on right underside of unit behind kickplate

assembly.

See Figure 4. Determine where you will connect

to hot water supply.

Review Figure 4 and note the location of

water inlet valve. Determine where you will connect the drain

hose.

Cut access holes for the Electrical, Water and Drain hoses in the

shaded areas as shown in Figure 2.

The dishwasher operates on a 120 volt, 60 Hz electrical supply.

Provide a separate circuit with a fuse or circuit breaker rated for

at least 15 amps (20 amps if connected with disposer) but not

more than 20 amps.

Pull electrical cable through hole into installation area.

Be sure water inlet valve is protected from freezing. If valve

freezes and ruptures, flooding may occur.

Determine amount of tubing needed to connect hot water supply

to the unit's water inlet valve. Extra hose length is necessary.

High-pressure and high-temperature

Stainless Flexible hosewith

a minimum inner diameter of V4"may be used. A shut-off valve

installed outside dishwasher cabinet is best.

Route water supply line into installation area.

9. Stand dishwasher back upright for further installation.

IMPORTANT:

Incoming hot water temperature

should be at

least 120°F (49°C). Water pressure should be between

20-90 psi.

Water Line

Brass Elbow

LElectrical

Line

(Not Included)

Figure

Property Damage

Do not use the furnished

drain hose or a rubber garden hose

for the water supply line. Either of these hoses can burst.

Flooding may occur and cause property damage.

EndStorage Location

NOTE: Pull the hose from "End Storage Location" side.

See images below to connect the Drain Hose.

Take drain Hose out of dishwasher and find the end that

doesn't have the black rubber material.

Use only the spring clamp that is provided in the accessory

kit, place spring clamp over one of the hoses. See Image

Below.

Take the plastic side of the drain hose and insert it into the

hose that is already attached to the dishwasher make sure

hose ends are flush against each other. See image below.

Secure the spring clamp 1/8" from large end of black hose to

the plastic side that was inserted for best sealing results.

See Image Below.

Plastic

Ends

of Hoses

Flush

Hose

Attached

to Dishwasher

Tighten Spring Clamp

Measure height of cabinet opening from underside ofcountertop

to floor. Check chart for height opening and suggested

adjustment.

Leg Leveler Adjustment

Chart

Heightof

NumberofTurns

Cabinet Opening

Adjust Levelers

34" (86.4cm)

34W' (86.7cm)

345he '' (87.2cm)

34_/2 '' (87.6cm)

Move dishwasher to front of installation area.

Loosen the rear leveling legs by turning counterclockwise.

Refer

to chart for number of turns.

Dishwasher Anchoring

Install the Cabinet Seal Kit (Instructions included in Kit)

Choose one of the methods of attachment below to secure unit,

holes need to be pre-drilled using a #5 drill bit regardless of

the option chosen:

a. Side Mount Cabinet Clips (Preferred Method of attachment)

b. Top Mount Cabinet Clips (to be used when Side Mount

is not an available option)

CAUTION:

Use extreme care in mounting the dishwasher as to not

scratch, bump or otherwise damage the console or tub.

To install the Side Mounting Clips.

Depending on space allowed in cabinet the Side Mounting

Clips can be installed with the holes for the screw up (preferred

method) or down as shown in the illustrations below. (Use extreme

caution when the clips are in the down position while installing

the dishwasher).

NOTE: Install Side Mount Brackets before unit is installed into

the cabinet. Insert screws into the front holes of the

mounting clips only. (See image below)

Use if measures

34V8" to 35"

Use if measures

34" to 34V_"

screw

To install using Top Mount Cabinet Clips:

Depending on the depth of cabinet, the Top Mount

Clip have a break off point that can be removed if

necessary.

NOTE: Install Top Mount Clips before unit is installed

into the

cabinet.

Screw clips firmly to top brace using screws

provided

in the literature

pack. (See image below)