Bosch PWS Manuel d'instructions original - Page 12
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions original pour {nom_de_la_catégorie} Bosch PWS. Bosch PWS 16 pages.
Imprimer la page
OBJ_BUCH-1824-001.book Page 22 Thursday, January 17, 2013 10:33 AM
22 | English
Angle Grinder
PWS ...
Article number
3 603 ...
Rated power input
Rated speed
min
Grinding disc diameter,
max.
mm
Thread of grinder spindle
Thread length (max.) of
grinder spindle
mm
Weight according to
EPTA-Procedure
01/2003 with standard-
auxiliary handle
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Helmut Heinzelmann
Senior Vice President
Head of Product Certification
Engineering
PT/ETM9
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
04.12.2012
Assembly
Mounting the Protective Devices
Before any work on the machine itself, pull the mains
plug.
Note: After breakage of the grinding disc during operation or
damage to the holding fixtures on the protection guard/power
tool, the machine must promptly be sent to an after-sales ser-
vice agent for maintenance for addresses, see section "After-
sales Service and Application Service".
2 609 006 763 | (17.1.13)
780-125
CA2 7..
W
780
-1
12000
125
M 14
21
kg
1.8
/II
Protection Guard for Grinding
of the work process. For this, press the release lever 1 up-
ward and turn the protection guard 6 to the required position.
Always adjust the protection guard 6 in such a manner
Adjust the protection guard 6 in such a manner that
The protection guard 6 may be turned only upon actua-
Note: The encoding keys on the protection guard 6 ensure
that only a protection guard that fits the machine type can be
mounted.
Protection Guard for Cutting
For cutting with bonded abrasives, always use the pro-
Provide for sufficient dust extraction when cutting
The protection guard for cutting 10 is mounted in the same
manner as the protection guard for grinding 6.
7800
850-115
CA2 7..
CA2 7..
780
850
12000
12000
125
115
M 14
M 14
21
21
1.8
1.8
/II
/II
Place the protection guard 6 onto
the spindle collar of the machine
until the encoding keys of the pro-
tection guard agree with the spin-
dle collar. Press and hold the re-
lease lever 1 while doing this.
Press the protection guard 6 onto
the spindle collar until the shoul-
der of the protection guard is
seated against the flange of the
machine, and turn the protection
guard until it can clearly be heard
to engage.
Adjust the position of the protec-
tion guard 6 to the requirements
that all 3 red cams of release lever 1 engage into the
corresponding notches of the protection guard 6.
sparking is prevented in the direction of the operator.
tion of the release lever 1! Otherwise the power tool
may not continue to be used under any circumstances
and must be taken to an after-sales service agent.
tection guard for cutting 10.
stone.
850-125
CA2 7..
850
12000
125
M 14
21
1.8
/II
Bosch Power Tools