Bosch SG450 Manuel d'utilisation et de sécurité - Page 3
Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation et de sécurité pour {nom_de_la_catégorie} Bosch SG450. Bosch SG450 33 pages.
Également pour Bosch SG450 : Manuel d'utilisation et de sécurité (32 pages)
Imprimer la page
BM 2610023125 02-12:BM 2610023125 02-12.qxp 2/8/12 2:21 PM Page 3
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment
or binding of moving parts, breakage of
parts and any other condition that may
affect the power tool's operation. If damaged,
have the power tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
Hold power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden
wiring or its own cord. Fasteners contacting
a "live" wire may make exposed metal parts of
the power tool "live" and could give the
operator an electric shock.
Do not drill, fasten or break into existing
walls or other blind areas where electrical
wiring may exist.
unavoidable, disconnect all fuses or circuit
breakers feeding this worksite.
Always wear safety goggles or eye
protection when using this tool. Dust and
debris may be expelled from the work piece
during normal operation.
Secure the material being fastened. Never
hold it in your hand or across legs.
Unstable support can cause the drill bit to
bind causing loss of control and injury.
Never leave the trigger locked "ON".
Before plugging the tool in, check that the
trigger lock is "OFF". Accidental start-ups
could cause injury.
Position the cord clear of rotating driver.
Do not wrap the cord around your arm or
wrist. If you lose control and have the cord
wrapped around your arm or wrist it may
entrap you and cause injury.
Be aware of the location and setting of the
switch "Lock-ON" button. If the switch is
Safety Rules for Screwsguns
If this situation is
-3-
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
Use the power tool, accessories and tool
bits etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the
safety of the power tool is maintained.
locked "ON" during the use, be ready for
emergency situations to switch it "OFF", by
first pulling the trigger then immediately
releasing it without pressing the "Lock-ON"
button.
Be prepared for a strong reaction torque
when "seating" or removing a screw. The
driver motor housing will tend to twist in the
opposite direction when "seating" or
removing a screw.
Do not use dull or damaged bits and
accessories. Bits and accessories in these
conditions may cause the tool to react in an
unpredictable manner.
Check to see that keys and adjusting
wrenches are removed from the driver
before switching the tool "ON". Keys or
wrenches can fly away at high velocity
striking you or a bystander.
Do not run the tool while carrying it at
your side. A spinning drill bit could become
entangled with clothing and injury may result.
Never place any part of your body in a
pinch point area. When operating auto-feed
attachment consider where your hand is
located. If it is within a pinch point, strongly
consider an alternative position. Injuries
occur when hands or fingers are between
moving and stationary parts during the
pinching movement.