Aleph QT-40SL Manuel - Page 2

Parcourez en ligne ou téléchargez le pdf Manuel pour {nom_de_la_catégorie} Aleph QT-40SL. Aleph QT-40SL 2 pages. Quad-tech intrusion detectors

Imprimer la page
Top View
0
3.0
1.5
4.5
6.0
7.5
9.0
10.5 12.0
28
25
20
15
10
5
0
5
10
15
20
25
28
0
5
10
15
20
25
30
35
40
ft
Note: Dashed lines indicate typical microwave coverage.
0
1.5 3 4.5
6
7.5 9 10.5 12 13.5 15 16.5 18
37
35
30
25
20
15
10
5
0
5
10
15
20
25
30
35
37
0
5
10 15 20 25 30 35 40 45 50 55 60
ft
Troubleshooting
Trouble
Likely Causes
Unit does not power up.
No or low input power.
Input power polarity reversed .
Alarm LED does not light.
Input power polarity reversed .
Incorrect sensor mounting height or aiming.
Pulse count setting incorrect for protection
area .
Alarm LED / Relay triggers
Animal / rodents in protection area.
without movement in the
Heating or a ir conditioning outlets in
protection area .
sensor view.
Pet access to furniture or room fixture in
An alarm is indicated at the LED
Incorrect wiring at the alarm output
but not at the alarm output.
Lightning damage.
Alarm LED on constantly, no fault
Defective unit.
in protected area or wiring .
Unit continues to operate after
The wire to the "-" power input was
input power has been discon-
nected.
Specifications
Microwave Freq.
Input Voltage
Input Current
15 mA max. (SL model 30 mA), 11 mA quiescent (approx.)
Pyro Type
Pulse Count
Warm-up Time
Alarm Period
Visual Indicator
Alarm Output
NC, solid state, 19 VDC, 100 mA, 13 ohms resistance typ.
Tamper Output
Mounting Height
Operating Temp.
Environmental
Weight
Dimensions
P/N 9-900-003-00 Rev.
Detection Patterns
QT-40 & QT-40SL Main Lens: 40WAPET Wide Angle
m
40ft (12m) L X 56ft (17m) W
8.5
7.5
6.0
1.5
3
0
4.5
8
3.0
1.5
0
1.5
3.0
4.5
0
6.0
0
5
10
ft
7.5
Lookdown
8.5
(Masked for PI)
m
QT-60 Main Lens: 60STD
10.5
60ft (18.3m) L X 74ft (22.6m) W
9
7.5
6
0
1.5
3
4.5
4.5
8
3
1.5
0
1.5
3
4.5
6
0
7.5
9
0
5
10
15
ft
10.5
Lookdown
view of the detector (pet immune unit).
terminals.
disconnected, the "+" is still connected.
The power is finding a return path
through the Alarm Output protection
device and alarm wiring.
10.525 GHz, pulsed
10 to 16 VDC, 12 VDC nominal
Dual Element
Jumper selectable: PC2, PC4
25 - 45 seconds
2.4 seconds, retriggerable
Red Alarm LED (Selectable On / Off)
NC, dry contact, 30 VDC, 500 mA, 5 W max.
7 to 8.5 ft (2.1 to 2.6 m)
14° to 131° F (-10° to 55° C)
95% humidity non-condensing
3 oz / 85 g
4.8" H x 2.5" W x 1.7" D / 12.2cm x 6.4cm x 4.3cm
© 2009 Aleph America Corporation
Side View
4.5
6
7.5
9
10.5
15
20
25
35
30
Mid Range
6
7.5
9
10.5
12
13.5
20
25
30
35
40
45
Mid Range
Remedy
Apply proper input voltage.
Correct wiring polarity.
Set LED jumper to "
L
E
D
EN
AB
L
E
D
"
Alter the mounting height or aim.
Set pulse count jumper to suit the
detection requirements.
Block access of animals / rodents.
Re-aim sensor.
Ensure that pets can not climb up onto
furniture / fixtures in protection area.
Correct the wiring fault .
Replace sensor.
R
e
p
a l
c
e
s
e
n
s
o
. r
Disconnect wire from the "+" power
input.
All rights reserved
FCC/IC Information:
FCC ID: DNHQT-001-00
IC: QT00100-xxxx
FCC/IC Statement:
m
12.0
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 and
2.4
ICES-003 of the FCC and Industry Canada Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
Long
accordance with the instructions, may cause harmful
Range
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
0
interference to radio or television reception, which can be
40
determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV
technician for help.
The user should not modify or change this equipment
m
15
16.5
18
without written approval from ALEPH.
Modification could void authority to use this equipment.
2.4
Note
• This detector is designed to be incorporated into an
Long
alarm system. As it is part of a system, Aleph cannot
Range
assume responsibility for theft or damage if the system
fails to operate.
0
50
55
60
Patent information
US & international patents pending
Maintenance
• INSPECTION: An inspection of this unit should be made periodically,
including, but not limited to all mounting, wiring, and the
condition of the interior area and components.
• CLEANING: Clean the external plastic parts of this unit with a soft,
.
clean, cloth dampened with water.
• TESTING:
This unit should be tested routinely for proper operation.
At a minimum, operation should be fully checked yearly.
Automatic LED Brightness Feature
The QT Series alarm LED indicator includes an automatic
brightness feature. In order to allow for a less noticeable
installation, LED brightness is reduced as the ambient light level
in the room drops.
The LED can be fully disabled by removing the ALARM LED
jumper.
Available accessories
• 100PET -- 100 lb pet immune lens (for QT-40 & QT-40SL only)
Contact Aleph
Nippon Aleph Corporation
-Security Products Headquarters-
1-28-52, Komaoka, Tsurimi-ku
Yokohama-shi, Kanagawa-ken
JAPAN, 230-0071
Tel: +81 045-575-4290 / Fax: +81 045-580-1676
WEB: http://www.nippon-aleph.co.jp
Aleph America Corporation
4700 Aircenter Cir, Reno, NV, 89502
USA
Tel: 775 827 8000 / Fax: 775 827 8044
WEB: http://www.aleph-usa.com
Aleph Europe Ltd.
1 Newton Close, Park Farm Industrial Estate
Wellingborough, Northamptonshire, NN8 6UW
England
Tel: 044 193 367 9600 / Fax: 044 193 340 1165
WEB: http://www.alepheurope.com