OBJ_BUCH-1555-004.book Page 8 Monday, November 16, 2015 2:39 PM
8 | English
Technical Data
Planer
Article number
Rated voltage
No-load speed
Planing depth
Rebating depth
Planing width, max.
Weight according to EPTA-Procedure 01/2003
Assembly
Before any work on the machine itself (e.g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Battery Charging (see figure A)
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The Lithium-Ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
To remove the battery 7 press the unlocking buttons 8 and
pull out the battery downwards. Do not exert any force.
The Allen key 12 required for replacement of the planer blade
is located inside the machine and should always be stored
there.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Battery Charge-control Indication (see figure B)
The three green LEDs of the battery charge-control indicator
14 indicate the charge condition of the battery 7. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 13 to indicate the charge condition. This is also
possible when the battery 7 is removed.
1 609 92A 1TS | (16.11.15)
GHO 14,4 V-LI
3 601 EA0 4..
V=
14.4
-1
min
14000
mm
0 –1.6
mm
0 –8
mm
82
kg
2.5
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 13, then the bat-
tery is defective and must be replaced.
Changing the Tool
Be cautious when replacing the planer blades. Do not
grasp the planer blades by the cutting edges. Possible
danger of injury due to the sharp cutting edges of the
planer blades.
Use only original Bosch carbide blades (TC).
The carbide blade (TC) has 2 cutting edges and can be re-
versed. When both cutting edges are dull, the planer blade
18 must be replaced. The carbide blade (TC) may not be re-
sharpened.
Disassembling the Planer Blade(s) (see figure C)
To reverse or replace the planer blade 18, rotate the blade
drum 15 until it is parallel to the planer base plate 10.
Loosen the two fastening screws 17 with the Allen key
12 by approx. 1 –2 turns.
If necessary, loosen the clamping element 16 by giving it
a light blow with a suitable tool (e.g. a wooden wedge).
Push the planer blade 18 sidewards out of the blade
drum 15 with a piece of wood.
Assembling the Planer Blade(s) (see figure D)
The guide groove of the planer blade always ensures continu-
ous height adjustment when replacing or reversing it.
If required, clean the blade seat in the clamping element 16
and the planer blade 18.
When assembling the planer blade, ensure that it is seated
properly in the blade holder of the clamping element 16 and
aligned flush at the side edge of the rear planer base plate 10.
Afterwards tighten the 2 fastening screws 17 again with the
Allen key 12.
Note: Before restarting, check if the fastening screws 17 are
tightened well. Rotate the blade drum 15 by hand and ensure
that the planer blade does not graze.
GHO 18 V-LI
3 601 EA0 3..
18
14000
0 –1.6
0 –8
82
2.6
Capacity
≥2/3
≥1/3
<1/3
Reserve
Bosch Power Tools
Imprimer la page