Electrolux EHD68210P Manuel de l'utilisateur - Page 14
Parcourez en ligne ou téléchargez le pdf Manuel de l'utilisateur pour {nom_de_la_catégorie} Electrolux EHD68210P. Electrolux EHD68210P 20 pages. E:line induction cooktop
Également pour Electrolux EHD68210P : Spécifications (18 pages), Manuel de l'utilisateur (16 pages), Manuel de dimensionnement et d'installation (1 pages)
Imprimer la page
14 electrolux
Installation instructions
Safety instructions
Warning! This must be read!
The laws, ordinances, directives and stand-
ards in force in the country of use are to be
followed (safety regulations, proper recycling
in accordance with the regulations, etc.)
Installation may only be carried out by a quali-
fied electrician. The minimum distances to
other appliances and units are to be ob-
served.
Anti-shock protection must be provided by
the installation, for example drawers may on-
ly be installed with a protective floor directly
underneath the appliance. The cut surfaces
of the worktop are to be protected against
moisture using a suitable sealant.
The sealant seals the appliance to the work
top with no gap. When building in, protect the
underside of the appliance from steam and
moisture, e.g. from a dishwasher or oven.
Avoid installing the appliance next to doors
and under windows. Otherwise hot cook-
ware may be knocked off the rings when
doors and windows are opened.
Warning! Risk of injury from electrical
current.
• The electrical mains terminal is live.
• Make electrical mains terminal free of volt-
age.
• Follow connection schematic.
• Observe electrical safety rules.
• Ensure anti-shock protection by installing
correctly.
• The appliance must be connected to the
electrical supply by a qualified electrician.
• Loose and inappropriate plug and socket
connections can make the terminal over-
heat.
• Have the clamping connections correctly
installed by a qualified electrician.
The connection must be carried out as
shown in the diagram, refer to the sticker
Caution! The surface temperature
exceeds 95°C. To avoid a hazard, under
bench access must be restricted.
on the back of the hob for wiring connec-
tion diagram. The connection links should
be fitted according the appropriate con-
nection diagram. Note for single phase
connection, the link (or bridge) will need to
be fitted between terminals 1 and 2 (refer
to the connection sticker on back of the
unit). The earth lead is connected to ter-
minal
.
The earth lead must be longer than leads
carrying electric current.
• Use strain relief clamp on cable.
• In the event of single-phase or two-phase
connection, the appropriate mains cable
of type H05BB-F Tmax 90°C (or higher)
must be used.
• If this appliance's mains cable is damaged,
it must be replaced by a special cable (type
H05BB-F Tmax 90°C; or higher). Please
contact your local Service Force Center for
further advice.
A device must be provided in the electrical
installation which allows the appliance to be
disconnected from the mains at all poles with
a contact opening width of at least 3 mm
Suitable isolation devices include line pro-
tecting cut-outs, fuses (screw type fuses are
to be removed from the holder), earth leak-
age trips and contactors.
Sticking on the seal
• Clean the worktop in the area of the cut-
out section.
• Stick the one-sided self-adhesive sealing
tape supplied all the way round the lower
edge of the cooking surface along the out-
er edge of the glass ceramic panel. Do not
stretch it. The cut ends should lie in the
middle of one side. When you have cut it
to length (add a few mm), press the two
ends flush up against one another.
A duplicate rating label is supplied with this
unit. For easy identification of this unit after
installation, stick it to a readily available sur-
face adjacent to the cooktop.