Dremel 290 Manuel d'instructions original - Page 4
Parcourez en ligne ou téléchargez le pdf Manuel d'instructions original pour {nom_de_la_catégorie} Dremel 290. Dremel 290 17 pages.
Imprimer la page
dusts are considered carcinogenic); wear a dust mask
and work with dust/chip extraction when connectable
SPECIFICATIONS
Model number . . . . . . . . 290
Voltage. . . . . . . . . . . . . . . 230 V/50-60 Hz
No-load speed . . . . . . . . . 6,000/min
Weight . . . . . . . . . . . . . . . 0.2 kg
Use completely unrolled and safe extension cords with
a capacity of 5 Amps.
Always check that the supply voltage is the same as
the voltage indicated on the nameplate of the tool.
GETTING STARTED
In order to use the engraver, you must first install the
engraver point. To properly install the engraver point,
loosen the set screw located in the engraver point holder
4
. Place the engraver point inside the point holder and
firmly tighten the set screw. It is important to make sure
the engraver point is held firmly in place by the set screw.
To remove a worn out engraver point, loosen the set screw
and remove the engraver point
points may be purchased from your Dremel dealer.
ON/OFF
To use the engraver, turn the engraver "ON" by moving the
on/off switch located at the end of the tool
HOLDING THE TOOL
Hold the engraver at a slight angle as you would normally
hold a pencil. Hold the unit lightly while resting your arm
comfortably on a table. Do not press down hard while
engraving. Use a light touch guiding the point over the
work somewhat slower than you would normally write.
DEPTH OF ENGRAVING
The adjusting knob on the side of the engraver housing
controls the stroke length and therefore the depth of
engraving
6
. It is not intended to be used as an "OFF"
switch. A good "rule of thumb" is to select the lowest
setting which will produce a deep enough engraving
mark to meet your requirements. To familiarize yourself,
experiment with different settings on scrap materials.
NOTE: With extended use, the positive detent indicator
associated with the depth control knob will begin to wear
down and be less noticeable. This is to be expected and
does not indicate malfunction of the engraver.
NOTE: The engraver point furnished with your engraver
is carbide steel. Do not engrave on electronic media such
as CDs, DVDs, etc. Engraving on these materials may
damage the media.
SERVICE AND WARRANTY
We recommend that all tool service be performed by a
Dremel Service Centre.
This Dremel product is guaranteed in accordance with
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling are
excluded from the warranty.
In case of a complaint, send the undismantled tool and/or
charger and proof of purchase to your dealer.
USE
4
. Replacement engraver
5
.
CONTACT DREMEL
For more information on service and warranty, the Dremel
product range, support and hotline, go to www.dremel.com.
NOISE AND VIBRATION
Sound pressure level (standard deviation 3dB) dB(A) 86.0
Sound power level (standard deviation 3dB) dB(A)
Vibration (triax vector sum) m/s
Vibration uncertainty K m/s
NOTE: The declared vibration total value has been
measured in accordance with a standard test method and
may be used for comparing one tool with another. It may
also be used in a preliminary assessment of exposure.
The vibration emission during actual use of the power tool
can differ from the declared total value depending on the
ways in which you use the tool.
Make an estimation of the exposure in the actual conditions
of use and identify the safety measures for personal
protection accordingly (taking account of all parts of the
operating cycle such as the times when the tool is switched
off and when it is running idle in addition to the trigger time).
The tool, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EC COUNTRIES
According the European Guideline 2012/19/EC for Waste
Electrical and Electronic Equipment and its implementation
into national right, power tools that are no longer usable
must be collected separately and disposed of in an
environmentally correct manner.
Информация о подтверждении соответствия, стране
происхождения, а также дате изготовления указана на
последней странице обложки руководства.
Контактная информация относительно импортера
содержится на упаковке.
ИСПОЛЬЗУЕМЫЕ СИМВОЛЫ
1
ПРОЧТИТЕ ДАННЫЕ ИНСТРУКЦИИ
2
КОНСТРУКЦИЯ II КЛАССА
3
НЕ ВЫБРАСЫВАЙТЕ ЭЛЕКТРОИНСТРУМЕНТЫ
ВМЕСТЕ С БЫТОВЫМ МУСОРОМ
ОБЩИЕ ПРЕДУПРЕЖДЕНИЯ ПО
БЕЗОПАСНОСТИ ПРИ ИСПОЛЬЗОВАНИИ
ЭЛЕКТРИЧЕСКОГО ИНСТРУМЕНТА
ПРОЧТИТЕ ВСЕ ИНСТРУКЦИИ И
ПРЕДУПРЕЖДЕНИЯ ПО
БЕЗОПАСНОСТИ
Несоблюдение этих инструкций и мер безопасности
может привести к поражению электрическим
4
2
2
DISPOSAL
3
RU
ОБЩИЕ
97.0
7.7
1.5