Atlantic TidalWave FP300 Series Manuel d'utilisation - Page 3

Parcourez en ligne ou téléchargez le pdf Manuel d'utilisation pour {nom_de_la_catégorie} Atlantic TidalWave FP300 Series. Atlantic TidalWave FP300 Series 4 pages.

Imprimer la page

• Fountain Series pumps must not be used to pump salt water, sewage, flammable or

corrosive liquids, greases, oils or food waste.

• Pay careful attention to the water level while the pump is operating. The pump must be

fully submersed at all times of operation.

• Repeating cycles of stopping and restarting will damage the water pump. Do not continue

operation at low water level or while the inlet is clogged with debris. Not only will perfor-

mance suffer, but also such conditions may cause noise, heavy vibration, and pump failure.

• In case of excessive vibration, unusual noise or odor, turn off the power immediately and

consult your nearest dealer.

Maintenance and Inspection

• Regular maintenance and inspections are a necessity for continued efficient functioning. If

any abnormal conditions are noticed, refer to the section on Troubleshooting and take

corrective measures immediately.

Monthly Inspection

• Check for any drop in performance. Reduced performance is usually caused by debris

blocking the pump intake.

• Detach the power cable from the receptacle or turn off the power supply (circuit breaker).

• Disconnect the pump discharge and remove the pump from the water.

• Remove any accumulated debris from the surface of the pump and pre-filter.

• Remove the pre-filter, inspect the adjustable flow and remove any accumulated debris.

• Remove volute by rotating it in a counterclockwise half turn while pulling lightly outward

from the pump body.

• Inspect the impeller. The impeller should spin freely. If the impeller feels tight or gritty

when spun, please refer to the cleaning instructions on page 5.

Winterizing

• Under no circumstances should the pump be left in frozen water.

• When the pump is out of use for an extended period, wash it and dry it thoroughly, then

store it indoors.

Note: Always run a test operation before putting the pump back into operation. When the

pump is left installed in water it should be run at regular intervals (about once per week).

Warranty

All TidalWave Fountain Series Pumps carry a two-year limited warranty. This limited

warranty is extended solely to the original purchaser commencing from the date of original

purchase receipt and is void if any of the following apply:

• The pump has been run while not fully submersed.

• The pump was not run on a dedicated circuit.

• The cord has been cut or altered.

• The pump has been misused or abused.

• Pump has been disassembled other than as described in this manual.

• Serial number tag has been removed.

Warranty Claims

• In case of warranty claims, pump should be returned to place of purchase accompanied

by original receipt.

Cleaning

Fountain pumps will require periodic cleaning of the magnetic rotor and rotor chamber.

Please follow the directions below for proper cleaning procedures:

• Remove the pre-filter.

• Remove the threaded inlet by rotating it in a counterclockwise half turn while pulling

lightly outward from the pump body.

• Remove the impeller assembly from the rotor chamber.

Note: The impeller assembly is comprised of six individual parts shown in the image below.

Take care not to lose or misplace any of these pieces during the cleaning process.

Pre-filter

Threaded

Inlet Cover

Flow Adjustor

Rubber Bushing

Ceramic Shaft

Friction Washer

• Inspect the magnetic rotor and the rotor chamber for built up debris. Loose debris can be

flushed out with clean water. Often in hard water, well water or pond-free applications,

debris may appear as a crusty film around the rotor and in the rotor chamber. Remove

this film using a scrub brush and white vinegar.

• Inspect the intake O-ring for nicks or breaks.

• Re-assemble the impeller assembly insert it into the rotor chamber.

• Attach the threaded inlet by applying pressure and rotating it in a clockwise half turn.

• Replace the pre-filter.

Rotor

Pump Body/Motor

Chamber

Impeller

Assembly

Rubber Feet

Impeller/

Magnetic Rotor